2005-2008 Yaris · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2005

HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE DOOR ARMREST COVER

B116818
  1. for 5 Door:
    Using a screwdriver with its tip wrapped in protective tape, disengage the 8 claws and 3 clips and remove the door armrest cover.

  1. B116851
    for 3 Door:
    Disengage the 12 claws and 3 clips and remove the door armrest cover.


3. REMOVE FRONT ARMREST BASE PANEL UPPER

B116819
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 5 claws and clip and remove the front armrest base panel upper.

  1. Disconnect the connector.


4. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B118070E01
  1. Remove the 3 screws and the power window regulator master switch.


5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY

B118071
  1. Disengage the 2 claws and remove the power window regulator switch.


6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

B107840
  1. Remove the 4 screws.

  1. B116821
    5 Door:
    Disengage the 8 clips.

  1. B116822
    3 Door:
    Disengage the 9 clips.

  1. B127219
    Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board.


7. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

B116945
  1. Disengage the 6 claws and remove the front door inside handle.


8. REMOVE FRONT DOOR GLASS WEATHERSTRIP INNER
  1. Remove the front door glass weatherstrip inner from the front door trim board.


9. REMOVE FRONT NO.1 SPEAKER ASSEMBLY

  1. E107768
    Disconnect the connector.

  1. Drill out the 3 rivet heads using a drill with a bit diameter of less than 4 mm (0.16 in.), and remove the front No.1 speaker assembly from the front door panel.

  1. Operate the drill around the rivet head circumference and cut out the flange.

    CAUTION:
    Be careful. The cut rivet is very hot.

    NOTICE:
    Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill the rivet head straight out.

  1. After drilling out the flange, continue drilling to push out the shards on the drill.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.


10. REMOVE FRONT DOOR WINDOW FRAME FRONT MOULDING

  1. B127705E01
    Using an infrared light, heat the front door window frame front moulding.

    CAUTION:
    Do not burn yourself with the heated front door panel or infrared light.

    HINT:
    Heat at 40 to 60 °C (104 to 140 °F) for 3 to 5 minutes.

  1. Disengage the 2 claws and remove the double-sided adhesive tape and the front door window frame front moulding.


11. REMOVE FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)

  1. B114605E01
    Using an infrared light, heat the front door window frame rear moulding.

    NOTICE:
    Do not burn yourself with the heated front door panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140°F) for 3 to 5 minutes.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 clips and the claw and remove the double-sided adhesive tape and front door window frame rear moulding.


12. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

B118045
  1. w/ Power mirror:
    Disconnect the connector.

  1. Remove the 3 nuts, disengage the claw and remove the outer rear view mirror.


13. REMOVE FRONT DOOR BELT MOULDING

  1. B114397E02
    for 5 Door:

    1. Apply protective tape to the door panel in the area around the front door belt moulding.

    2. B114398E02
      Using a moulding remover, disengage the 5 claws and the clip and remove the front door belt moulding.

  1. B114612E01
    for 3 Door:

    1. Apply protective tape to the door panel in the area around the front door moulding.

    2. B114613E01
      Using a moulding remover, disengage the 5 claws and remove the front door belt moulding.


14. REMOVE FRONT DOOR SERVICE HOLE COVER

B116823
  1. for 5 Door:
    Disconnect the connectors and clamps, then remove the front door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.

  1. B116824
    for 3 Door:
    Disconnect the connectors and clamps, then remove the front door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.


15. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
  1. Driver side:
    Provisionally install the power window regulator master switch.

  1. Passenger side:
    Provisionally install the power window regulator switch.

  1. B116825
    Move the front door glass until the 2 bolts appear in the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Do not drop or damage the front door glass when removing the bolts.

  1. B116827
    Remove the front door glass in the direction indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.

  1. Driver side:
    Remove the power window regulator master switch.

  1. Passenger side:
    Remove the power window regulator switch.


16. REMOVE FRONT DOOR GLASS RUN

B116826
  1. Remove the front door glass run.


17. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

B116828E01
  1. Disconnect the connector.

  1. Loosen bolt A.

  1. Remove the 5 bolts, then remove the front door window regulator.

    NOTICE:
    Do not drop or damage the window regulator when removing the bolts.

    HINT:
    Remove the window regulator through the service hole.


18. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY FRONT

B127222E01
  1. Using "Torx" socket wrench T25, remove the 3 screws and power window regulator motor.


19. REMOVE FRONT DOOR CHECK ASSEMBLY

B116830
  1. Remove the 3 bolts, then remove the front door check.

    NOTICE:
    Do not drop or damage the door check when removing the bolts.

    HINT:
    Remove the door check through the service hole.


20. REMOVE FRONT DOOR WEATHERSTRIP

B116833
  1. for 5 Door:
    Disengage the 35 clips and remove the front door weatherstrip.

    NOTICE:
    Remove any tape remaining on the door side.

  1. for 3 Door:
    Disengage the 37 clips and remove the front door weatherstrip.

    NOTICE:
    B116834
    Remove any tape remaining on the door side.


21. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER

B116831
  1. Remove the bolt, then remove the front door frame sub-assembly rear lower.

    NOTICE:
    Do not drop or damage the front door frame sub-assembly rear lower when removing the bolt.

    HINT:
    Remove the front door frame sub-assembly rear lower through the service hole.


22. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER

B116832
  1. Remove the 2 bolts and screw, then remove the front door frame sub-assembly front lower.

    NOTICE:
    Do not drop or damage the front door frame sub-assembly front lower when removing the bolts.

    HINT:
    Remove the front door frame sub-assembly front lower through the service hole.


23. REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP

B116835
  1. Slide the front door fix window weatherstrip, in the direction indicated by the arrow in the illustration, to remove it.

  1. Remove the front door fix window glass from the front door fix window weatherstrip.


24. REMOVE FRONT DOOR OUTSIDE HANDLE COVER

B116837
  1. Remove the hole plug.

  1. Using "Torx" socket wrench T30, loosen the screw and remove the cover with the door lock key cylinder installed.


25. REMOVE FRONT DOOR LOCK ASSEMBLY

B116836
  1. Using "Torx" socket wrench T30, remove the 3 screws.

  1. Move the front door lock downward, remove the outside handle frame link and remove the front door lock.

    NOTICE:
    Do not drop or damage the front door lock when removing the screws.

    HINT:
    Remove the front door lock through the service hole.

  1. B121552
    Open the cover.

  1. B121553
    Disconnect the front door lock remote control cable and front door inside locking cable.

  1. Remove the door lock wire harness seal.


26. REMOVE FRONT DOOR HANDLE ASSEMBLY OUTSIDE

B116838
  1. w/ Entry and start system:
    Disconnect the connector.

  1. Remove the handle by sliding and pulling it in the direction indicated by the arrow mark in the illustration.


27. REMOVE FRONT DOOR OUTSIDE HANDLE PAD REAR

B116839
  1. Disengage the 2 claws and remove the front door outside handle pad rear.


28. REMOVE FRONT DOOR OUTSIDE HANDLE PAD FRONT

B116840
  1. Disengage the 2 claws and remove the front door outside handle pad front.


29. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

B116841
  1. w/ Entry and start system:
    Disconnect the 2 connectors and clamp.

  1. Using "Torx" socket wrench T30, loosen the screw.

  1. Slide the front outside handle frame to remove it.


30. REMOVE CUSHION
  1. Remove the 2 cushions from the door panel.

← COMPONENTS (from Aug 2005)ADJUSTMENT (from Aug 2005) →