2005-2008 Yaris · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built from Jan 2006

HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

B136189
  1. Insert a clip remover between the plate and door trim.

  1. Turn the handle with the clip remover inserted, as shown in the illustration.

  1. Remove the front door window regulator handle and clip.

  1. Remove the window regulator handle plate.


3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

B136157E01
  1. Disengage the claw and clip and remove the front door lower frame bracket garnish.


4. REMOVE FRONT ARMREST BASE UPPER PANEL

B136158
  1. for Driver side with power window:

    1. Remove the screw.

    2. Disengage the 7 claws and 2 clips and remove the front armrest base upper panel.

    3. Disconnect the connector.

  1. B140702
    for Front passenger side with power window:

    1. Remove the screw.

    2. Disengage the 7 claws and 2 clips and remove the front armrest base upper panel.

    3. Disconnect the connector.

  1. B136191
    w/o Power window:

    1. Remove the screw.

    2. Disengage the 5 claws and 2 clips and remove the front armrest base upper panel.


5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Power Window)

B136183
  1. Remove the 3 screws and the power window regulator master switch.


6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (w/ Power Window)

B141906
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the power window regulator switch.


7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

  1. B136159
    w/ Power window:

    1. Remove the screw.

    2. B136160
      Disengage the 9 clips.

    3. B136161
      Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board.

  1. B136193
    w/o Power window:

    1. Remove the screw.

    2. B136192
      Disengage the 9 clips.

    3. B136194
      Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board.


8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

B136188
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the front door inside handle.


9. REMOVE FRONT DOOR GLASS WEATHERSTRIP INNER
  1. Remove the front door glass weatherstrip inner from the front door trim board.


10. REMOVE FRONT NO.1 SPEAKER ASSEMBLY

  1. E107768
    Disconnect the connector.

  1. Drill out the 3 rivet heads using a drill with a bit diameter of less than 4 mm (0.16 in.), and remove the front No.1 speaker assembly from the front door panel.

  1. Operate the drill around the rivet head circumference and cut out the flange.

    CAUTION:
    Be careful. The cut rivet is very hot.

    NOTICE:
    Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill the rivet head straight out.

  1. After drilling out the flange, continue drilling to push out the shards on the drill.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.


11. REMOVE OUTER REAR VIEW MIRROR

B136162E01
  1. w/ Power mirror:
    Disconnect the connector.

  1. Remove the 3 nuts, disengage the claw and remove the outer rear view mirror.


12. REMOVE FRONT DOOR BELT MOULDING

  1. B134873E02
    Apply protective tape to the door panel in the periphery of the front door belt moulding.

  1. B134874E02
    Using a moulding remover, disengage the 6 claws and remove the front door belt moulding.


13. REMOVE FRONT DOOR TRIM BRACKET

B136164
  1. Remove the 2 screws and front door trim bracket.


14. REMOVE FRONT DOOR SERVICE HOLE COVER

B136163
  1. Disconnect the connectors and clamps, then remove the front door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.


15. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
  1. w/ Power window:

    1. Driver side:
      Provisionally install the power window regulator master switch.

    2. Passenger side:
      Provisionally install the power window regulator switch.

  1. w/o Power window:

    1. Provisionally install the front door window regulator handle.

  1. B136165
    Move the front door glass until the 2 bolts can be seen through the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Do not drop or damage the front door glass when removing the bolts.

  1. B136166
    Remove the front door glass in the direction indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.

  1. w/ Power window:

    1. Driver side:
      Remove the power window regulator master switch.

    2. Passenger side:
      Remove the power window regulator switch.

  1. w/o Power window:

    1. Remove the front door window regulator handle.


16. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

B136167E01
  1. w/ Power window:

    1. Disconnect the connector.

    2. Loosen bolt A.

    3. Remove the 5 bolts, then remove the front door window regulator.

      NOTICE:
      Do not drop or damage the window regulator when removing the bolts.

      HINT:
      Remove the window regulator through the service hole.

  1. B136195E01
    w/o Power window:

    1. Loosen bolt A.

    2. Remove the 5 bolts, then remove the front door window regulator.

      NOTICE:
      Do not drop or damage the window regulator when removing the bolts.

      HINT:
      Remove the window regulator through the service hole.


17. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY FRONT (w/ Power Window)

B127213
  1. Using "Torx" socket wrench T25, remove the 3 screws and power window regulator motor.


18. REMOVE FRONT DOOR GLASS RUN

B136168
  1. Disengage the clip, then remove the front door glass run.


19. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER

B136170
  1. Remove the bolt, then remove the front door frame sub-assembly rear lower.

    NOTICE:
    Do not drop or damage the front door frame sub-assembly rear lower when removing the bolt.

    HINT:
    Remove the front door frame sub-assembly rear lower through the service hole.


20. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER

B136171
  1. Remove the bolt, then remove the front door frame sub-assembly front lower.

    NOTICE:
    Do not drop or damage the front door frame sub-assembly front lower when removing the bolt.

    HINT:
    Remove the front door frame sub-assembly front lower through the service hole.


21. REMOVE FRONT DOOR OUTSIDE HANDLE COVER

B136172
  1. Remove the hole plug.

  1. Using "Torx" socket wrench T30, loosen the screw and remove the cover with the door lock key cylinder installed.


22. REMOVE FRONT DOOR LOCK

B136169
  1. Using "Torx" socket wrench T30, remove the 3 screws.

  1. Move the front door lock downward, remove the outside handle frame link and remove the front door lock.

    NOTICE:
    Do not drop or damage the front door lock when removing the screws.

    HINT:
    Remove the front door lock through the service hole.

  1. B121552
    Open the cover.

  1. B121553
    Disconnect the front door lock remote control cable and front door inside locking cable.

  1. Remove the door lock wire harness seal.


23. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

B136173
  1. Remove the handle by sliding and pulling it in the directions indicated by the arrow mark in the illustration.


24. REMOVE FRONT DOOR OUTSIDE HANDLE PAD REAR

B136175
  1. Disengage the 2 claws and remove the front door outside handle pad rear.


25. REMOVE FRONT DOOR OUTSIDE HANDLE PAD FRONT

B136176
  1. Disengage the 2 claws and remove the front door outside handle pad front.


26. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

B116861
  1. Using "Torx" socket wrench T30, loosen the screw.

  1. Slide the front outside handle frame to remove it.


27. REMOVE FRONT DOOR CHECK ASSEMBLY

B136180
  1. Remove the 3 bolts, then remove the front door check.

    NOTICE:
    Do not drop or damage the door check when removing the bolts.

    HINT:
    Remove the door check through the service hole.


28. REMOVE FRONT DOOR WEATHERSTRIP

B136181
  1. Disengage the 35 clips and remove the front door weatherstrip.

    NOTICE:
    Remove any tape remaining on the door side.


29. REMOVE FRONT DOOR STIFFENER CUSHION (w/ Stiffener Cushion)

B136179
  1. Remove the bolt and front door stiffener cushion.


30. REMOVE CUSHION

B136182
  1. Remove the 2 cushions from the door panel.

← COMPONENTS (from Jan 2006)ADJUSTMENT (from Jan 2006) →