2005-2008 Yaris · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Jan 2006


1. INSTALL CUSHION

B136182
  1. Install the 2 cushions onto the door panel.


2. INSTALL FRONT DOOR STIFFENER CUSHION (w/ Stiffener Cushion)

B136179
  1. Install the front door stiffener cushion with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


3. INSTALL FRONT DOOR WEATHERSTRIP

B136181
  1. Engage the 35 clips and install the front door weatherstrip.


4. INSTALL FRONT DOOR CHECK ASSEMBLY

B136180
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the front door check onto the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. Install the front door check onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


5. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

B116862
  1. Using "Torx" socket wrench T30, install the front outside handle frame with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


6. INSTALL FRONT DOOR OUTSIDE HANDLE PAD FRONT

B136176
  1. Engage the 2 claws and install the front door outside handle pad front.


7. INSTALL FRONT DOOR OUTSIDE HANDLE PAD REAR

B136175
  1. Engage the 2 claws and install the front door outside handle pad rear.


8. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

B136174
  1. Pushing the front door outside handle in the direction of the arrow mark shown in the illustration, install the front door outside handle.


9. INSTALL FRONT DOOR LOCK

NOTICE:
  1. If reusing a door lock that has been removed, replace the packing in the connecting part with new.
  2. Make sure that no grease and dirt adheres to the packing surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.

  1. B121553
    Connect the front door lock remote control cable and front door inside locking cable.

  1. B121552
    Close the cover.

  1. B116845
    Insert the door lock open rod into the front door lock, then set it to the door panel.

    NOTICE:
    Make sure that the outside handle link is securely engaged with the door lock.

  1. B136169
    Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. Using "Torx" socket wrench T30, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


10. INSTALL FRONT DOOR OUTSIDE HANDLE COVER

B136172
  1. Using "Torx" socket wrench T30, install the cover with the door lock key cylinder.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the door lock key cylinder rod is inserted.

  1. Install the hole plug.


11. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER

B136171
  1. Install the front door frame sub-assembly front lower with the bolt.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }


12. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER

B136170
  1. Install the front door frame sub-assembly rear lower with the bolt.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }


13. INSTALL FRONT DOOR GLASS RUN

B136168
  1. Install the front door glass run, then engage the clip.


14. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY FRONT (w/ Power Window)

B127213
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using "Torx" socket wrench T25, install the power window regulator motor assembly front with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


15. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator.

    NOTICE:
    Do not apply grease to the window regulator spring.

  1. w/ Power window:

    1. B136167E01
      Loosely screw bolt A onto the front door window regulator.

    2. Insert the front door window regulator into the door panel. Use bolt A to hang the front door window regulator on the door panel.

      NOTICE:
      Do not drop the window regulator as it may be damaged.

    3. Install the front door window regulator with the 5 bolts, and tighten bolt A.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    4. Connect the connector.

  1. B136195E01
    w/o Power window:

    1. Loosely screw bolt A onto the front door window regulator.

    2. Insert the front door window regulator into the door panel. Use bolt A to hang the front door window regulator on the door panel.

      NOTICE:
      Do not drop the window regulator as it may be damaged.

    3. Install the front door window regulator with the 5 bolts, and tighten bolt A.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    4. Connect the connector.


16. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

B136186
  1. Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.

  1. B136165
    Install the front door glass onto the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


17. INSTALL FRONT DOOR SERVICE HOLE COVER

B136187E01
  1. Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.

    Adhesive:
    Part No. 08850-00065, Butyl Tape Set or the equivalent

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.


18. INSTALL FRONT DOOR TRIM BRACKET

  1. B136164
    Install the front door trim bracket with the 2 screws.


19. INSTALL FRONT DOOR BELT MOULDING

  1. B134875
    Engage the 6 claws and install a new front door belt moulding.

  1. B134873E02
    Remove the protective tape.


20. INSTALL OUTER REAR VIEW MIRROR

B136162E01
  1. Engage the claw and install the outer rear view mirror with the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. w/ Power mirror:
    Connect the connector.


21. INSTALL FRONT NO.1 SPEAKER ASSEMBLY

  1. E107769E01
    Using an air riveter or hand riveter, install the front No. 1 speaker assembly onto the front door panel with 3 new strike rivets.

    HINT:
    Install the new strike rivets in the order shown in the illustration.

    NOTICE:

    1. H002440
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    2. H002441
      Confirm that the rivets are seated properly against the speaker.
    3. Do not tilt the riveter when installing the rivet onto the speaker.
    4. Do not leave any space between the rivet head and speaker.

    5. H002442
      Do not leave any space between the speaker and door. Firmly hold the 2 items together while installing the rivet.

  1. E107770
    Connect the connector.


22. INSTALL FRONT DOOR GLASS WEATHERSTRIP INNER
  1. Install the front door glass weatherstrip inner onto the front door trim board.


23. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

B136237
  1. Engage the 4 claws and install the front door inside handle.


24. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

  1. B136161
    w/ Power window:

    1. Connect the front door lock remote control cable and front door inside locking cable.

    2. B136160
      Engage the 9 clips and install the front door trim board.

    3. B136159
      Tighten the screw.

  1. w/o Power window:

    1. B136194
      Connect the front door lock remote control cable and front door inside locking cable.

    2. B136192
      Engage the 9 clips and install the front door trim board.

    3. B136193
      Tighten the screw.


25. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Power Window)

B136183
  1. Install the power window regulator master switch with the 3 screws.


26. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (w/ Power Window)

B141906
  1. Engage the 2 claws and install the power window regulator switch.


27. INSTALL FRONT ARMREST BASE UPPER PANEL

B136158
  1. for Driver side with power window:

    1. Connect the connector.

    2. Engage the 7 claws and 2 clips and install the front armrest base upper panel.

    3. Tighten the screw.

  1. B140702
    for Front passenger side with power window:

    1. Connect the connector.

    2. Engage the 7 claws and 2 clips and install the front armrest base upper panel.

    3. Tighten the screw.

  1. B136191
    w/o Power window:

    1. Engage the 5 clips and 2 clips and install the front armrest base upper panel.

    2. Tighten the screw.


28. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

B136157E01
  1. Engage the claw and clip and install the front door lower frame bracket garnish.


29. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

B136196E01
  1. Install the window regulator handle plate.

  1. Open all the windows.

  1. B129030E01
    Install the front door window regulator handle with the clip at the angle shown in the illustration.


30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← ADJUSTMENT (from Jan 2006)COMPONENTS (from Aug 2005) →