2005-2008 Yaris · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Aug 2005


1. INSTALL CUSHION
  1. Install the 2 cushions onto the door panel.


2. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

B116862
  1. Using "Torx" socket wrench T30, install the front outside handle frame with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


3. INSTALL FRONT DOOR OUTSIDE HANDLE PAD FRONT

B116840
  1. Engage the 2 claws and install the front door outside handle pad front.


4. INSTALL FRONT DOOR OUTSIDE HANDLE PAD REAR

B116839
  1. Engage the 2 claws and install the front door outside handle pad rear.


5. INSTALL FRONT DOOR HANDLE ASSEMBLY OUTSIDE

B116860
  1. Pushing the front door handle assembly outside in the direction of the arrow mark shown in the illustration, install the front door handle assembly outside.


6. INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
  1. If reusing a door lock that has been removed, replace the packing in the connecting part with new.
  2. Make sure that no grease and dirt adheres to the packing surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.

  1. B121553
    Connect the front door lock remote control cable and front door inside locking cable.

  1. B121552
    Close the cover.

  1. B116845
    Insert the door lock open rod into the front door lock, then set it to the door panel.

    NOTICE:
    Make sure that the outside handle link is securely engaged with the door lock.

  1. B116836
    Apply adhesive to the threads of the screws.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or the equivalent

  1. Using "Torx" socket wrench T30, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


7. INSTALL FRONT DOOR OUTSIDE HANDLE COVER

B116858
  1. Using "Torx" socket wrench T30, install the cover with the door lock key cylinder.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the door lock key cylinder rod is inserted.

  1. Install the hole plug.


8. INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP
  1. Install the front door fix window glass onto the front door fix window weatherstrip.

  1. B116846
    Slide the front door fix window weatherstrip, in the direction indicated by the arrow in the illustration, to install it.


9. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER

B116832
  1. Install the front door frame sub-assembly front lower with the 2 bolts and screw.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }


10. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER

B116831
  1. Install the front door frame sub-assembly rear lower with the bolt.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }


11. INSTALL FRONT DOOR WEATHERSTRIP

B116833
  1. for 5 Door:
    Engage the 35 clips and install the front door weatherstrip.

  1. B116834
    for 3 Door:
    Engage the 37 clips and install the front door weatherstrip.


12. INSTALL FRONT DOOR CHECK ASSEMBLY

B116830
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the front door check onto the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or the equivalent

  1. Install the front door check onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


13. INSTALL FRONT DOOR WINDOW REGULATOR
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator sub-assembly.

    NOTICE:
    Do not apply grease to the window regulator spring.

  1. B116857E01
    Loosely screw bolt A onto the front door window regulator sub-assembly.

  1. Insert the front door window regulator into the door panel. Use bolt A to hang the front door window regulator on the door panel.

    NOTICE:
    Do not drop the window regulator as it may be damaged.

  1. Install the front door window regulator with the 4 bolts, and tighten bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


14. INSTALL FRONT DOOR GLASS RUN

B116826
  1. Install the front door glass run.


15. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

B116847
  1. Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.

  1. B116825
    Install the front door glass onto the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


16. INSTALL FRONT DOOR SERVICE HOLE COVER

B116848E01
  1. for 5 Door:
    Apply butyl tape to the door panel, then install the front door service hole cover as shown in the illustration.

    Adhesive:
    Part No. 08850-00065, Butyl Tape Set or the equivalent

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.

  1. B116849E01
    for 3 Door:
    Apply butyl tape to the door panel, then install the front door service hole cover as shown in the illustration.

    Adhesive:
    Part No. 08850-00065, Butyl Tape Set or the equivalent

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.


17. INSTALL FRONT DOOR BELT MOULDING

  1. B114401
    for 5 Door:

    1. Engage the 5 claws and the clip and install a new front door belt moulding.

    2. B114397E02
      Remove the protective tape.

  1. B114614
    for 3 Door:

    1. Engage the 5 claws and the clip and install a new front door belt moulding.

    2. B114612E01
      Remove the protective tape.


18. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

B118045
  1. Engage the claw, then install the outer rear view mirror with the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. w/ Power mirror:
    Connect the connector.


19. INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)

  1. B114606E01
    Clean the attachment surface.

    1. Using an infrared light, heat the adhesive remaining on the body.

      NOTICE:
      Do not burn yourself with the heated body or infrared light.

    2. Using a shop rag or piece of cloth, rub the remaining adhesive off the body.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Apply new double-sided adhesive tape to the front door window frame rear moulding.

    Tape size: 
    Area
    t
    W
    H
    A
    0.8 mm (0.032 in.)
    5 mm (0.197 in.)
    340 mm (13.386 in.)
    B
    0.8 mm (0.032 in.)
    5 mm (0.197 in.)
    376 mm (14.803 in.)

  1. B114607
    Engage the 2 clips and the claw and install the front door window frame rear moulding.


20. INSTALL FRONT DOOR WINDOW FRAME FRONT MOULDING

  1. B127706E01
    Clean the attachment surface.

    1. Using an infrared light, heat the adhesive remaining on the body.

      NOTICE:
      Do not burn yourself with the heated body or infrared light.

    2. Using a shop rag or piece of cloth, rub the remaining adhesive off the body.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Apply new double-sided adhesive tape to the front door window frame front moulding.

    Tape size: 
    Area
    t
    W
    H
    A
    1.2 mm (0.047 in.)
    7 mm (0.276 in.)
    88 mm (3.465 in.)

  1. B127705E01
    Engage the 2 clips and the claw and install the front door window frame front moulding.


21. INSTALL FRONT NO.1 SPEAKER ASSEMBLY

  1. E107769E01
    Using an air riveter or hand riveter, install the front No. 1 speaker assembly onto the front door panel with 3 new strike rivets.

    HINT:
    Install the new strike rivets in the order shown in the illustration.

    NOTICE:

    1. H002440
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    2. H002441
      Confirm that the rivets are seated properly against the speaker.
    3. Do not tilt the riveter when installing the rivet onto the speaker.
    4. Do not leave any space between the rivet head and speaker.

    5. H002442
      Do not leave any space between the speaker and door. Firmly hold the 2 items together while installing the rivet.

  1. E107770
    Connect the connector.


22. INSTALL FRONT DOOR GLASS WEATHERSTRIP INNER
  1. Install the front door glass weatherstrip inner onto the front door trim board.


23. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

B116945
  1. Engage the 6 claws and install the front door inside handle.


24. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

B127219
  1. Connect the front door lock remote control cable and front door inside locking cable.

  1. B116856
    for 5 Door:
    Engage the 8 clips and install the front door trim board.

  1. B116822
    for 3 Door:
    Engage the 9 clips and install the front door trim board.

  1. B107840
    Tighten the 4 screws.


25. INSTALL FRONT ARMREST BASE PANEL UPPER

B116854
  1. Engage the 5 claws and clip and install the front door armrest base panel upper.


26. INSTALL DOOR ARMREST COVER

B116852
  1. for 5 Door:
    Engage the 8 claws and 3 clips and install the door armrest cover.

  1. B116853
    for 3 Door:
    Engage the 12 claws and 4 clips and install the door armrest cover.


27. INSTALL DOOR WINDOW REGULATOR HANDLE ASSEMBLY

B116863
  1. Install the window regulator handle plate.

  1. Open all the windows.

  1. B116947E01
    Install the front door window regulator handle with clip at the angle shown in the illustration.


28. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← ADJUSTMENT (from Aug 2005)COMPONENTS (from Jan 2006) →