2005-2008 Yaris · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Jan 2006


1. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
  1. Apply MP grease to the sliding areas of the rear door outside handle frame.

  1. B136227
    Slide the outside handle frame to install it.


2. INSTALL REAR DOOR OUTSIDE HANDLE PAD FRONT

B136225
  1. Engage the 2 claws and install the rear door outside handle pad front.

  1. B136224
    Using "Torx" socket wrench T30, tighten the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


3. INSTALL REAR DOOR OUTSIDE HANDLE PAD REAR

B136223
  1. Engage the 2 claws and install the rear door outside handle pad rear.


4. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

B136222
  1. Pushing the rear door outside handle in the direction of the arrow mark shown in the illustration, install the rear door outside handle.


5. INSTALL REAR DOOR OUTSIDE HANDLE COVER

B136220
  1. Using "Torx" socket wrench T30, install the rear door outside handle cover with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


6. INSTALL REAR DOOR LOCK

NOTICE:
  1. If reusing a door lock that has been removed, replace the packing in the connecting part with new.
  2. Make sure that no grease or dirt adheres to the packing surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.

  1. B127211
    Connect the rear door lock remote control cable and rear door inside locking cable.

  1. B121554
    Close the 2 covers.

  1. Insert the door lock into the outside handle frame release plate, then set it onto the door panel.

  1. Make sure that the outside handle frame link is securely engaged with the door lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. B136218
    Using "Torx" socket wrench T30, install the rear door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


7. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR (w/ Power Window)

B116929
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using "Torx" socket wrench T25, install the power window regulator motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


8. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. w/ Power window:

    1. Apply MP grease to the sliding and rotating areas of the rear door window regulator.

      NOTICE:
      Do not apply grease to the window regulator spring.

    2. B136217E01
      Loosely screw bolt A onto the rear door window regulator.

    3. Insert the rear door window regulator into the door panel. Use bolt A to hang the rear door window regulator on the door panel.

      NOTICE:
      Do not drop the window regulator as it may be damaged.

    4. Install the rear door window regulator with the 3 bolts, and tighten bolt A.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    5. Connect the connector.

  1. w/o Power window:

    1. Apply MP grease to the sliding and rotating areas of the rear door window regulator.

      NOTICE:
      Do not apply grease to the window regulator spring.

    2. B136232
      Install the rear door window regulator with the 3 bolts.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


9. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

B136216
  1. w/ Power window:

    1. Install the rear door glass onto the rear door window regulator.

  1. B136231
    w/o Power window:

    1. Install the rear door glass onto the rear door window regulator.


10. INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP

B136219
  1. Install the rear door quarter window glass onto the rear door quarter window weatherstrip.

  1. B136228
    Slide the rear door quarter window weatherstrip, in the direction indicated by the arrow in the illustration, to install it.


11. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

B136214
  1. Install the rear door window division bar with the 2 bolts and screw.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }


12. INSTALL REAR DOOR GLASS RUN

B136213
  1. Install the rear door glass run.


13. INSTALL REAR DOOR BELT MOULDING

  1. B134882
    Engage the 5 claws and install a new rear door belt moulding.

  1. B134880E03
    Remove the protective tape.


14. INSTALL REAR DOOR WEATHERSTRIP

B136212
  1. Engage the 32 clips and install the rear door weatherstrip.


15. INSTALL REAR DOOR CHECK ASSEMBLY

B136211
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the rear door check onto the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. Install the rear door check onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


16. INSTALL REAR DOOR SERVICE HOLE COVER

  1. B136230E01
    Apply butyl tape to the door panel, then install a new rear door service hole cover as shown in the illustration.

    Adhesive:
    Part No. 08850-00065, Butyl Tape Set or the equivalent

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.


17. INSTALL REAR DOOR TRIM BRACKET

  1. B136209
    Install the rear door trim bracket with the 2 screws.


18. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY REAR (w/ Power Window)

B136234
  1. Engage the set plate and install the power window regulator switch.


19. INSTALL REAR DOOR GLASS WEATHERSTRIP INNER
  1. Install the rear door glass weatherstrip inner onto the rear door trim board.


20. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

B136236
  1. Engage the 4 claws and install the rear door inside handle.


21. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

B136208
  1. Connect the rear door lock remote control cable and rear door inside locking cable.

  1. w/ Power window:
    Connect the connector.

  1. B136207
    Engage the 7 clips and install the rear door trim board.

  1. B136206
    Tighten the screw.


22. INSTALL REAR DOOR ARMREST BASE UPPER PANEL

B136205
  1. Engage the 4 claws and install the rear door armrest base upper panel.


23. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

B136197E01
  1. Install the window regulator handle plate.

  1. Open all the windows.

  1. B129030E01
    Install the rear door window regulator handle with the clip at the angle shown in the illustration.


24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← ADJUSTMENT (from Jan 2006)COMPONENTS (from Aug 2005) →