2005-2008 Yaris · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2005

HINT:
  1. Use the same procedure for both the RH and LH side.
  2. The procedure described below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE DOOR WINDOW REGULATOR HANDLE ASSEMBLY

B116942
  1. Insert a clip remover between the plate and door trim.

  1. Turn the handle with the clip remover inserted, as shown in the illustration.

  1. Remove the rear door window regulator handle assembly and clip.

  1. Remove the window regulator handle plate.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

B116864
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the rear door armrest plug.

  1. B116939
    Remove the 2 screws.

  1. B116940
    Disengage the 7 clips.

  1. Disconnect the connector.

  1. B116941
    Disconnect the rear door lock remote control cable and rear door inside locking cable and remove the rear door trim board.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

B116946
  1. Disengage the 6 claws and remove the rear door inside handle.


5. REMOVE REAR DOOR GLASS WEATHERSTRIP INNER
  1. Remove the rear door glass weatherstrip inner from the rear door trim board.


6. REMOVE REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

  1. E107771
    Disconnect the connector.

  1. Drill out the 3 rivet heads using a drill with a bit diameter of less than 4 mm (0.16 in.), and remove the rear speaker assembly from the rear door panel.

  1. Operate the drill around the rivet head circumference and cut out the flange.

    CAUTION:
    Be careful. The cut rivet is very hot.

    NOTICE:
    Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill the rivet head straight out.

  1. After drilling out the flange, continue drilling to push out the shards on the drill.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.


7. REMOVE REAR DOOR SERVICE HOLE COVER

B116871
  1. w/ Rear speaker:
    Disconnect the connectors and clamps, then remove the rear door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.

  1. B116872
    w/o Rear speaker:
    Disconnect the connectors and clamps, then remove the rear door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.


8. REMOVE REAR DOOR CHECK ASSEMBLY

B116875
  1. Remove the 3 bolts, then remove the rear door check.

    NOTICE:
    Do not drop or damage the door check when removing the bolts.

    HINT:
    Remove the door check through the service hole.


9. REMOVE REAR DOOR WEATHERSTRIP

B116876
  1. Disengage the 32 clips and remove the rear door weatherstrip.

    NOTICE:
    Remove any tape remaining on the door side.


10. REMOVE REAR DOOR BELT MOULDING

  1. B114404E01
    Apply protective tape to the door panel in the area around the rear door belt moulding.

  1. B114405E01
    Using a moulding remover, disengage the 5 claws and the clip and remove the rear door belt moulding.


11. REMOVE REAR DOOR GLASS RUN

B116877
  1. Remove the rear door glass run.


12. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

B116924
  1. Remove the 2 bolts and screw and rear door window division bar.

    NOTICE:
    Do not drop or damage the rear door window division bar when removing the 2 bolts and screw.


13. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP

B116925
  1. Slide the rear door quarter window weatherstrip, in the direction indicated by the arrow in the illustration, to remove it.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.


14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

B116944
  1. Remove the rear door glass from the rear door window regulator.


15. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

B116943E01
  1. Loosen bolt A.

  1. Remove the 2 bolts, then remove the rear door window regulator.

    NOTICE:
    Do not drop or damage the window regulator when removing the 2 bolts.

    HINT:
    Remove the window regulator through the service hole.


16. REMOVE REAR DOOR OUTSIDE HANDLE COVER

B116931
  1. Using "Torx" socket wrench T30, remove the screw and rear door outside handle cover.


17. REMOVE REAR DOOR LOCK ASSEMBLY

B116930
  1. Using "Torx" socket wrench T30, remove the 3 screws.

  1. Move the rear door lock downward, remove the outside handle frame release plate and remove the rear door lock.

    NOTICE:
    Do not drop or damage the rear door lock when removing the screws.

    HINT:
    Remove the rear door lock through the service hole.

  1. B121554
    Open the 2 covers.

  1. B127211
    Disconnect the rear door lock remote control cable and rear door inside locking cable.

  1. Remove the door lock wire harness seal.


18. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

B116932
  1. Remove the handle by sliding and pulling it in the direction indicated by the arrow mark in the illustration.


19. REMOVE REAR DOOR OUTSIDE HANDLE PAD REAR

B116934
  1. Disengage the 2 claws and remove the rear door outside handle pad rear.


20. REMOVE REAR DOOR OUTSIDE HANDLE PAD FRONT

B116935
  1. Using "Torx" socket wrench T30, loosen the screw.

  1. B116936
    Disengage the 2 claws and remove the rear door outside handle pad front.


21. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

B116937
  1. Slide the outside handle frame to remove it.

← COMPONENTS (from Aug 2005)ADJUSTMENT (from Aug 2005) →