2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. INSTALL BRAKE PEDAL PAD
  1. Install the brake pedal pad onto the brake pedal.


2. INSTALL BRAKE PEDAL BUSH
  1. Apply lithium soap base glycol grease to the 2 bushes.

  1. Install the 2 bushes onto the brake pedal.


3. INSTALL BRAKE PEDAL
  1. Install the brake pedal onto the pedal support with the brake pedal shaft and nut.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


4. INSTALL BRAKE PEDAL SUPPORT

C116881
  1. Install the pedal support with the bolt and 4 nuts.

    Torque:
    Bolt:
    24 N*m{ 241 kgf*cm , 17 ft.*lbf }
    Nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


5. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
  1. Apply lithium soap base glycol grease to the push rod pin.

  1. C116880
    Install the push rod clevis with the push rod pin and clip.

  1. Install the brake pedal return spring.


6. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER

C116879
  1. Install a new stop light switch mounting adjuster onto the pedal support.


7. INSTALL STOP LIGHT SWITCH

F049043E01
  1. Insert the stop light switch into the adjuster until it just touches the brake pedal.

    NOTICE:
    Do not depress the brake pedal.

  1. F049044E08
    Make a quarter turn clockwise to install the stop light switch.

    NOTICE:
    Do not depress the brake pedal.

    HINT:
    The turning torque for installing the stop light switch:

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

  1. Check the stop light switch clearance.

    Stop light switch clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)

  1. Connect the wire harness clamp onto the pedal support.

  1. Connect the connector to the stop light switch.


8. INSPECT AND ADJUST BRAKE PEDAL
  1. w/ Instrument Panel Under Cover:

    1. Remove the instrument panel under cover (Click here).

  1. C116874E01
    Inspect the brake pedal height.

    Pedal height from floor:
    w/ ABS, w/ VSC
    w/o ABS
    107.3 to 117.3 mm
    (4.224 to 4.618 in.)
    107.8 to 117.8 mm
    (4.244 to 4.638 in.)

    If the pedal height is incorrect, adjust it.

  1. Adjust the brake pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Turn the stop light switch counterclockwise, and remove the stop light switch.

    3. Loosen the push rod lock nut.

    4. Adjust the pedal height by turning the pedal push rod.

      Pedal height from floor:
      w/ ABS, w/ VSC
      w/o ABS
      107.3 to 117.3 mm
      (4.224 to 4.618 in.)
      107.8 to 117.8 mm
      (4.244 to 4.638 in.)

    5. Tighten the push rod lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. F049043E01
      Insert the stop light switch into the adjuster until it just touches the brake pedal.

      NOTICE:
      Do not depress the brake pedal.

    7. F049044E08
      Make a quarter turn clockwise to install the stop light switch.

      NOTICE:
      Do not depress the brake pedal.

      HINT:
      The turning torque for installing the stop light switch:

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    8. Check the stop light switch clearance.

      Stop light switch clearance:
      0.5 to 2.6 mm (0.020 to 0.102 in.)

    9. Connect the connector to the stop light switch.

  1. F048932E01
    Inspect the brake pedal free play.

    1. Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.

    2. Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

      Pedal free play:
      1.0 to 6.0 mm (0.039 to 0.236 in.)

      If incorrect, troubleshoot the brake system.

  1. R000934E02
    Inspect the brake pedal reserve distance.

    1. Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance as shown.

      Pedal reserve distance from floor at 300 N (31 kgf, 67.4 lbf):
      w/ ABS:
      Rear Brake
      LHD
      RHD
      Drum
      More than 73 mm (2.87 in.)
      More than 71 mm (2.80 in.)
      Disc
      More than 80 mm (3.15 in.)
      More than 80 mm (3.15 in.)
      w/o ABS:
      LHD
      RHD
      More than 70 mm (2.75 in.)
      -
      w/ VSC:
      LHD
      RHD
      More than 85 mm (3.35 in.)
      More than 75 mm (2.95 in.)

      HINT:
      1. If incorrect, troubleshoot the brake system.
      2. Sound and resistance from the brake booster when the brake pedal is depressed without a vacuum does not indicate a problem.

  1. w/ Instrument Panel Under Cover:

    1. Install the instrument panel under cover (Click here).


9. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

G028410E01
  1. Connect all the connectors and clamp the wire harnesses onto the steering post assembly bracket.

  1. Align the matchmarks on steering intermediate shaft assembly No. 2 and the steering sliding yoke and provisionally install them with bolt C.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Align the matchmarks on the steering sliding yoke and steering gear assembly and install them with bolt B.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }


10. INSTALL COLUMN HOLE COVER SILENCER SHEET

A116501
  1. Install the column hole cover plate with the 2 clips.

  1. Install the floor carpet.


11. INSTALL INSTRUMENT PANEL UNDER TRAY (w/o Driver Side Knee Airbag)

B108187
  1. Engage the 4 claws and install the instrument panel under tray.

  1. Install the 2 <A> screws.

  1. B108186
    Engage the 4 claws and install the instrument panel under tray.


12. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

C125678E01
  1. Engage the 6 claws.

  1. Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


13. INSTALL STEERING COLUMN COVER (w/ Driver Side Knee Airbag)

  1. C118007
    Engage the 2 claws and install the steering column cover (lower).

  1. Tighten the 3 screws.


14. INSTALL STEERING COLUMN COVER SUPPORT (w/ Driver Side Knee Airbag)

B108275E01
  1. Engage the 4 claws to install the steering column cover support.


15. INSTALL INSTRUMENT PANEL NO. 1 UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel No. 1 Under Cover Sub-assembly)

  1. B114572
    Engage the 3 claws and install the instrument panel under cover.

  1. Tighten the 2 screws.


16. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

B108233E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the upper side of the instrument panel.

  1. Engage the claw and the 3 clips at the lower side of the instrument panel.

    B105355E01

  1. Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt

  1. Connect the connectors.

    B105354E01

  1. B108182
    Connect the passenger airbag connector and clamp.


17. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B105352
  1. Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.

  1. B108202
    Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.


18. INSTALL NO. 1 SWITCH HOLE BASE

B108201
  1. Disengage the 2 clips and 2 claws and install the switch hole base.


19. INSTALL FRONT PILLAR GARNISH RH

  1. B114342E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127672
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127674
      Connect the speaker connector.

  1. B114312
    Install the 3 antenna cord clamps.

  1. Connect the connector.

  1. w/ Curtain Shield Airbag:

    1. B117697E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B117694
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


20. INSTALL FRONT PILLAR GARNISH LH

  1. B114344E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127671
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127673
      Connect the speaker connector.

  1. B114316
    Install the 4 wire harness clamps.

  1. w/ Curtain Shield Airbag:

    1. B117698E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B114318
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


21. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.


22. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.


23. INSTALL COMBINATION METER ASSEMBLY

E107730
  1. Install the combination meter assembly with the 2 screws.

  1. Connect the 2 connectors.


24. INSTALL INSTRUMENT CLUSTER FINISH PANEL

B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. B132367
    Engage the 4 claws and 5 clips and install the instrument cluster finish panel.


25. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

E107743
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.

  1. E107744
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.


26. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

E107741
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.

  1. E107742
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.


27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


28. INSPECT SRS WARNING LIGHT
(Click here)
← REMOVAL (from Aug 2005)COMPONENTS (from Nov 2005) →