INSTALLATION
Removal / installation · Vehicles built from Nov 2005
| 1. INSTALL BRAKE PEDAL PAD |
Install the brake pedal pad onto the brake pedal.
| 2. INSTALL BRAKE PEDAL BUSH |
Apply lithium soap base glycol grease to the 2 bushes.
Install the 2 bushes onto the brake pedal.
| 3. INSTALL BRAKE PEDAL |
Install the brake pedal onto the pedal support with the brake pedal shaft and nut.
- Torque:
- 37 N*m{ 375 kgf*cm , 27 ft.*lbf }
| 4. INSTALL BRAKE PEDAL SUPPORT |
![]() ![]() |
Install the pedal support with the bolt and 4 nuts.
- Torque:
- Bolt:
- 24 N*m{ 241 kgf*cm , 17 ft.*lbf }
- Nut:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
| 5. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS |
Apply lithium soap base glycol grease to the push rod pin.
Install the push rod clevis with the push rod pin and clip.

Install the brake pedal return spring.
| 6. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER |
![]() ![]() |
Install a new stop light switch mounting adjuster onto the pedal support.
| 7. INSTALL STOP LIGHT SWITCH |
![]() ![]() |
Insert the stop light switch into the adjuster until it just touches the brake pedal.
- NOTICE:
- Do not depress the brake pedal.
Make a quarter turn clockwise to install the stop light switch.

- NOTICE:
- Do not depress the brake pedal.
- HINT:
- The turning torque for installing the stop light switch:
- Torque:
- 1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less
Check the stop light switch clearance.
- Stop light switch clearance:
- 0.5 to 2.6 mm (0.020 to 0.102 in.)
Connect the wire harness clamp onto the pedal support.
Connect the connector to the stop light switch.
| 8. INSPECT AND ADJUST BRAKE PEDAL |
Remove the instrument panel under cover (Click here).
Inspect the brake pedal height.

- Pedal height from floor:
- 107.3 to 117.3 mm (4.224 to 4.618 in.)
Adjust the brake pedal height.
Disconnect the connector from the stop light switch.
Turn the stop light switch counterclockwise, and remove the stop light switch.
Loosen the push rod lock nut.
Adjust the pedal height by turning the pedal push rod.
- Pedal height from floor:
- 107.3 to 117.3 mm (4.224 to 4.618 in.)
Tighten the push rod lock nut.
- Torque:
- 15 N*m{ 153 kgf*cm , 11 ft.*lbf }
Insert the stop light switch into the adjuster until it just touches the brake pedal.

- NOTICE:
- Do not depress the brake pedal.
Make a quarter turn clockwise to install the stop light switch.

- NOTICE:
- Do not depress the brake pedal.
- HINT:
- The turning torque for installing the stop light switch:
- Torque:
- 1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less
Check the stop light switch clearance.
- Stop light switch clearance:
- 0.5 to 2.6 mm (0.020 to 0.102 in.)
Connect the connector to the stop light switch.
Inspect the brake pedal free play.

Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.
Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.
- Pedal free play:
- 1.0 to 6.0 mm (0.039 to 0.236 in.)
Inspect the brake pedal reserve distance.

Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance as shown.
- Pedal reserve distance from floor at 300 N (31 kgf, 67.4 lbf):
- for Gasoline engine:
Rear Brake
LHD
RHD
Drum
More than 75 mm (2.95 in.)
More than 72 mm (2.83 in.)
Disc
More than 75 mm (2.95 in.)
More than 75 mm (2.95 in.)
- for Diesel engine:
Rear Brake
LHD
RHD
Drum
More than 72 mm (2.83 in.)
More than 65 mm (2.56 in.)
Disc
More than 74 mm (2.91 in.)
More than 72 mm (2.83 in.)
- HINT:
- Sound and resistance from the brake booster when the brake pedal is depressed without a vacuum does not indicate a problem.
Install the instrument panel under cover (Click here).
| 9. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() ![]() |
Connect all the connectors and clamp the wire harnesses onto the steering column assembly bracket.
Align the matchmarks on steering intermediate shaft assembly No. 2 and the steering sliding yoke and provisionally install them with bolt C.
- Torque:
- 28 N*m{ 290 kgf*cm , 21 ft.*lbf }
Align the matchmarks on the steering sliding yoke and steering gear assembly and install them with bolt B.
- Torque:
- 28 N*m{ 290 kgf*cm , 21 ft.*lbf }
Tighten bolt A.
- Torque:
- 28 N*m{ 290 kgf*cm , 21 ft.*lbf }
| 10. INSTALL COLUMN HOLE COVER SILENCER SHEET |
![]() ![]() |
Install the column hole cover plate with the 2 clips.
Install the floor carpet.
| 11. INSTALL INSTRUMENT PANEL UNDER TRAY (w/o Driver Side Knee Airbag) |
![]() ![]() |
Engage the 4 claws and install the instrument panel under tray.
Install the 2 <A> screws.
Engage the 4 claws and install the instrument panel under tray.

| 12. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag) |
![]() ![]() |
Engage the 6 claws.
Install the driver side knee airbag assembly with the 4 bolts.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
| 13. INSTALL STEERING COLUMN COVER (w/ Driver Side Knee Airbag) |
Engage the 2 claws and install the steering column cover (lower).

Tighten the 3 screws.
| 14. INSTALL STEERING COLUMN COVER SUPPORT (w/ Driver Side Knee Airbag) |
![]() ![]() |
Engage the 4 claws to install the steering column cover support.
| 15. INSTALL INSTRUMENT PANEL NO. 1 UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel No. 1 Under Cover Sub-assembly) |
Engage the 3 claws and install the instrument panel under cover.

Tighten the 2 screws.
| 16. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() ![]() |
Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).
Engage the 5 claws at the upper side of the instrument panel.
Engage the claw and the 3 clips at the lower side of the instrument panel.


Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt
Connect the connectors.


Connect the passenger airbag connector and clamp.

| 17. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() ![]() |
Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.
- NOTICE:
- Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.
Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.

| 18. INSTALL NO. 1 SWITCH HOLE BASE |
![]() ![]() |
Disengage the 2 clips and 2 claws and install the switch hole base.
| 19. INSTALL FRONT PILLAR GARNISH RH |
w/ Curtain Shield Airbag:

Remove the piece of cloth or nylon.
w/ Front No. 2 Speaker:

Insert the hook into the body hole.
Engage the clip and install the front speaker.
Connect the speaker connector.

Install the 3 antenna cord clamps.

Connect the connector.
w/ Curtain Shield Airbag:
Install a new special clip and the clip onto a new front pillar garnish.

Engage the 2 clips and the 2 claws and install the front pillar garnish.
w/o Curtain Shield Airbag:
Engage the 2 clips and the 2 claws and install the front pillar garnish.

| 20. INSTALL FRONT PILLAR GARNISH LH |
w/ Curtain Shield Airbag:

Remove the piece of cloth or nylon.
w/ Front No. 2 Speaker:

Insert the hook into the body hole.
Engage the clip and install the front speaker.
Connect the speaker connector.

Install the 4 wire harness clamps.

w/ Curtain Shield Airbag:
Install a new special clip and the clip onto a new front pillar garnish.

Engage the 2 clips and the 2 claws and install the front pillar garnish.
w/o Curtain Shield Airbag:
Engage the 2 clips and the 2 claws and install the front pillar garnish.

| 21. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Install the front door opening trim weatherstrip.
| 22. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Install the front door opening trim weatherstrip.
| 23. INSTALL COMBINATION METER ASSEMBLY |
![]() ![]() |
Install the combination meter assembly with the 2 screws.
Connect the 2 connectors.
| 24. INSTALL INSTRUMENT CLUSTER FINISH PANEL |
![]() ![]() |
Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.
Engage the 4 claws and 5 clips and install the instrument cluster finish panel.

| 25. INSTALL INSTRUMENT PANEL FINISH PANEL END RH |
![]() ![]() |
with CD player
Connect the connector.
Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.
Except CD player

Connect the connector.
Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.
| 26. INSTALL INSTRUMENT PANEL FINISH PANEL END LH |
![]() ![]() |
with CD player
Connect the connector.
Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.
Except CD player

Connect the connector.
Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.
| 27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 28. INSPECT SRS WARNING LIGHT |














