2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. INSTALL MANIFOLD ABSOLUTE PRESSURE SENSOR

A104790
  1. Install the manifold absolute pressure sensor with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.


2. INSTALL THROTTLE BODY GASKET

A104785E01
  1. Install a new gasket onto the intake manifold.


3. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

A117080
  1. Install the throttle body with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf }

  1. Connect the connector.

  1. Connect the 2 water by-pass hoses.


4. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

A116530E01
  1. Install the air cleaner cap with the 2 clamps.

  1. Tighten the 4 clamps.


5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


6. ADD ENGINE COOLANT
  1. Tighten all the plugs.

  1. Disconnect the vinyl hose.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    4.5 liters (4.8 USqts, 4.2 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (c) through (h) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add engine coolant.


7. CHECK FOR ENGINE COOLANT LEAKAGE

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A107403
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump it to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.

← INSPECTION (from Aug 2005)COMPONENTS (from Aug 2005) →