2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

A116179
  1. Apply a light coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.

    NOTICE:
    Do not twist the O-ring.

  1. A116178
    Install the camshaft timing oil control valve assembly with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. A116177
    Connect the camshaft timing oil control vales assembly connector.


2. INSTALL FAN BELT ADJUSTING BAR

A115508
  1. Provisionally install the fan belt adjusting bar with the bolt and nut.

  1. Tighten the nut to the specified torque.

    Torque:
    11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }


3. INSTALL FAN AND GENERATOR V BELT
  1. Provisionally install the fan and generator V belt onto each pulley.

    NOTICE:
    Make sure that the V-belt is securely fitted into the rib groove of the pulley.


4. ADJUST FAN AND GENERATOR V BELT

  1. A116198E01
    for Unleaded Gasoline Specification Vehicle:
    Insert an adjusting bar between the engine mounting bracket and generator assembly. Push the adjusting bar towards the vehicle front to adjust the generator V belt tension.

    NOTICE:
    Do not insert the adjusting bar between the camshaft timing oil control valve assembly and generator assembly. It could damage the camshaft timing oil control valve assembly.

  1. A117470
    for Leaded Gasoline Specification Vehicle:
    Insert the adjusting bar between the engine mounting bracket and generator assembly. Push the adjusting bar towards the vehicle front to adjust the generator V belt tension.

  1. A116197E01
    First tighten bolt A, then tighten bolt B.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf } for bolt A
    54 N*m{ 551 kgf*cm , 40 ft.*lbf } for bolt B


5. INSPECT FAN AND GENERATOR V BELT

  1. A116200E01
    Check the V belt deflection and tension.

    Deflection:
    Item
    Specified Condition
    New belt
    7.0 to 8.5 mm (0.28 to 0.33 in)
    Used belt
    11 to 13 mm (0.43 to 0.51 in)

    Tension:
    Item
    Specified Condition
    New belt
    539 to 637 N (55 to 65 kg, 121 to 143 ld)
    Used belt
    245 to 392 N (25 to 40 kg, 55 to 88 ld)

    If the belt deflection is not as specified, adjust it.

    HINT:
    1. Check the V belt deflection at the specified point.
    2. Check the drive belt deflection at the specified point.
    3. When installing a new belt, set its tension to the specified value.
    4. When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.
    5. When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of each Used Belt specification.
    6. V-ribbed belt tension and deflection should be checked after 2 revolutions of engine cranking.
    7. When using a belt tension gauge, confirm its accuracy by using a master gauge first.


6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


7. CHECK FOR ENGINE OIL LEAKAGE

8. INSTALL CYLINDER HEAD COVER NO. 2

A116235E01
  1. Tighten 2 A nuts, then 2 B nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


9. INSTALL ENGINE UNDER COVER RH

10. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)
← INSPECTION (from Aug 2005)COMPONENTS (from Aug 2005) →