2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jan 2006

Versions by build date: Aug 2005 – Dec 2005 from Jan 2006


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE FRONT WHEEL RH

3. REMOVE ENGINE UNDER COVER RH

4. DRAIN ENGINE OIL

5. DRAIN ENGINE COOLANT

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.

  1. Loosen the cylinder block drain cock plug, then drain the coolant.

    A106596E01


6. REMOVE CYLINDER HEAD COVER NO. 2

A116235
  1. Remove the 4 nuts and cylinder head cover No. 2.


7. REMOVE FAN AND GENERATOR V BELT

  1. A116197E01
    Loosen bolts A and B.

  1. Release the fan and generator V belt tension and remove the fan and generator V belt.


8. REMOVE GENERATOR ASSEMBLY

A115418
  1. Remove the terminal cap.

  1. Separate the connector and harness clamp.

  1. Remove the nut and remove terminal B.

  1. A115419E01
    Remove fan belt adjusting slider fixing bolts A and B and remove the fan belt adjusting slider.

  1. A115420E01
    Remove fixing bolt B and remove the generator.


9. REMOVE IGNITION COIL NO. 1

A115484
  1. Disconnect the 4 ignition coil connectors.

  1. A115485
    Remove the 4 bolts and 4 ignition coils.


10. DISCONNECT VENTILATION HOSE

A115487
  1. Disconnect the ventilation hose.


11. DISCONNECT VENTILATION HOSE NO. 2

A115488
  1. Disconnect ventilation hose No. 2.


12. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for RHD)

A115489
  1. Disconnect the fuel injector connectors.

  1. A116181
    Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.

  1. A066472E01
    Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.


13. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for LHD)

A115489
  1. Disconnect the fuel injector connectors.

  1. A115490
    Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.

  1. A115491
    Remove the bolt and remove the wire harness bracket.

  1. A066472E01
    Remove the 9 bolts, 2 nuts and 2 seal washers and remove the cylinder head cover sub-assembly.


14. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

A116236
  1. Place a wooden block on a jack underneath the engine.

  1. G100143
    Remove the 5 bolts and nut and remove the engine mounting insulator sub-assembly RH.


15. REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY

A116203E01

  1. Set cylinder No. 1 to TDC/compression.

    1. Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump.

    2. A116204E01
      Check that the timing marks on the camshaft timing sprocket and the camshaft timing gear are all facing upward as shown in the illustration.
      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.

  1. A116552E01
    Using 2 SSTs, loosen the bolt while holding the crankshaft damper sub-assembly.
    SST
    09213-14010   (91651-60865)
    09330-00021  

    NOTICE:
    Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.

  1. Remove the SSTs and the bolt.

  1. Remove the crankshaft damper sub-assembly.


16. REMOVE CRANKSHAFT POSITION SENSOR

A091817
  1. Disconnect the crankshaft position sensor connector.

  1. Remove the bolt and remove the crankshaft position sensor.


17. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

A116177
  1. Disconnect the camshaft timing oil control valve assembly connector.

  1. A116178
    Remove the bolt and nut and remove the camshaft timing oil control valve assembly.

  1. A116179
    Remove the O-ring from the camshaft timing oil control valve assembly.


18. REMOVE WATER PUMP PULLEY

A116191E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 3 bolts and remove the water pump pulley.


19. REMOVE WATER PUMP ASSEMBLY

A116192
  1. Remove the 3 bolts and 2 nuts and remove the water pump assembly and gasket.


20. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

A116553
  1. Remove the 4 bolts and remove the transverse engine engine mounting bracket.


21. REMOVE OIL PUMP ASSEMBLY

A116554
  1. Remove the 15 bolts and the nut.

  1. A116555
    Using a screwdriver with its tip wrapped in protective tape, prize the oil pump assembly to remove it.

    NOTICE:
    Do not damage the contact surfaces of the oil pump assembly or oil pan sub-assembly.

  1. A116556
    Remove the 2 O-rings from the cylinder block and oil pan sub-assembly.


22. REMOVE OIL PUMP SEAL

A035281
  1. Using a screwdriver with its tip wrapped in protective tape, remove the oil pump seal.


23. REMOVE CHAIN TENSIONER ASSEMBLY NO. 1

NOTICE:
  1. Do not rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40 ° from the TDC first.

  1. A116564E01
    Pull up the stopper plate and hold it with its lock released.

  1. A116565E01
    Unlock the plunger of the tensioner and push it in to the end.

  1. A116566E01
    Pull down the stopper plate with the plunger pushed to the end and lock the plunger.

  1. A116567
    Insert a 3 mm (0.12 in.) diameter bar into the hole in the stopper plate and lock the plunger.

  1. A116568
    Remove the 2 bolts and remove chain tensioner assembly No. 1.


24. REMOVE CHAIN TENSIONER SLIPPER

A116569
  1. Remove the chain tensioner slipper.


25. REMOVE CHAIN VIBRATION DAMPER NO. 1

A116570
  1. Remove the 2 bolts and remove chain vibration damper No. 1.


26. REMOVE CHAIN SUB-ASSEMBLY
← REMOVAL (Aug 2005 – Dec 2005)INSPECTION (from Aug 2005) →