2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jan 2006

Versions by build date: Aug 2005 – Dec 2005 from Jan 2006


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE ENGINE UNDER COVER RH

3. REMOVE CYLINDER HEAD COVER NO. 2

A116235
  1. Remove the 4 nuts and cylinder head cover No. 2.


4. REMOVE IGNITION COIL NO. 1

A115484
  1. Disconnect the 4 ignition coil connectors.

  1. A115485
    Remove the 4 bolts and 4 ignition coils.


5. DISCONNECT VENTILATION HOSE

A115487
  1. Disconnect the ventilation hose.


6. DISCONNECT VENTILATION HOSE NO. 2

A115488
  1. Disconnect ventilation hose No. 2.


7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for RHD)

A115489
  1. Disconnect the fuel injector connectors.

  1. A116181
    Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.

  1. A066472E01
    Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.


8. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for LHD)

A115489
  1. Disconnect the fuel injector connectors.

  1. A115490
    Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.

  1. A115491
    Remove the bolt and remove the wire harness bracket.

  1. A066472E01
    Remove the 9 bolts, 2 nuts and 2 seal washers and remove the cylinder head cover sub-assembly.


9. REMOVE FAN AND GENERATOR V BELT

  1. A116197E01
    Loosen bolts A and B.

  1. Release the fan and generator V belt tension and remove the fan and generator V belt.


10. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

A116236
  1. Place a wooden block on a jack underneath the engine.

  1. G100143
    Remove the 5 bolts and nut and remove the engine mounting insulator sub-assembly RH.


11. REMOVE NO. 2 CAMSHAFT

A116206E01

NOTICE:
When rotating the camshaft with the timing chain removed, rotate the crankshaft damper counterclockwise 40 ° from the TDC and align its timing notch with the matchmark of the timing chain cover to prevent the pistons from coming into contact with the valves.

  1. Set No. 1 cylinder to TDC/compression.

    1. A116203E01
      Turn the crankshaft damper, and align its timing notch with the timing mark "0" of the oil pump.

    2. A116204E01
      Check that both timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward, as shown in the illustration.

      HINT:
      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.

  1. A116207E01
    Place paint marks on the chain in place where the timing marks of the camshaft timing sprocket and the camshaft timing gear are located.

  1. G100163
    Using an 8 mm hexagon wrench, remove the screw plug.

  1. A116209E01
    Insert a screwdriver into the service hole in the chain tensioner to pull the stopper plate of the chain tensioner upward.

  1. A116210E01
    Using a wrench, rotate camshaft No. 2 clockwise to push in the plunger of the chain tensioner.

  1. A116212
    Remove the screwdriver from the service hole, then align the hole in the stopper plate with the service hole and insert a 3 mm (0.12 in.) diameter bar into the holes to hold the stopper plate.

    HINT:
    1. Fix the stopper plate using the bar while rotating the camshaft right and left slightly.
    2. Hold the bar with tape so that the bar does not come off.

  1. A116213
    Using a wrench, hold the hexagonal lobe of camshaft No. 2 and remove the fringe bolt.

  1. A116214E01
    Using several steps, loosen and remove the 11 bearing cap bolts uniformly in the sequence shown in the illustration, then remove camshaft bearing cap No. 1 and camshaft bearing cap No. 2.

    NOTICE:
    Loosen each bolt uniformly while keeping the camshaft level.

  1. A116215
    Remove the flange bolt and remove the camshaft timing sprocket.

  1. A116216
    Remove camshaft No. 2.


12. REMOVE CAMSHAFT

  1. A116217E01
    Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration, then remove camshaft bearing cap No. 2.

    NOTICE:
    Loosen each bolt uniformly while keeping the camshaft level.

  1. A116218
    Hold the chain by hand, and remove the camshaft and the camshaft timing gear assembly.

  1. A035227E01
    Tie the chain with a piece of string as shown in the illustration.


13. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Clamp the camshaft in a vise and confirm that it is locked.

    NOTICE:
    Do not damage the camshaft.

  1. A116226E03
    Cover the 4 oil paths of the cam journal with tape as shown in the illustration.

    HINT:
    One of the 2 grooves located on the cam journal is for retarding cam timing (upper) and the other is for advancing cam timing (lower). Each groove has 2 oil paths. Plug one of the oil paths for each groove with a piece of rubber before wrapping the cam journal with the tape.

  1. Puncture the tape covering the advance oil path and the retard oil path on the opposite side from the advance oil path.

  1. A116227E02
    Apply air at about 150 kPa (1.5kgf*cm2) pressure into the 2 broken paths (the advance side path and the retard side path).

    NOTICE:
    Cover the paths with a shop rag or piece of cloth to prevent oil splashes.

  1. A116228E02
    Confirm that the camshaft timing gear assembly revolves in the timing advance direction when the air pressure on the timing retard path is reduced.

    HINT:
    The lock pin is released, and the camshaft timing gear revolves in the advance direction.

  1. When the camshaft timing gear reaches the most advanced position, release the air pressure on the timing retard side path, and then release the air pressure on the timing advance side path.

    NOTICE:
    The camshaft timing gear assembly occasionally shifts to the retard side abruptly, if the air pressure on the advance side path is released first. This often results in the breakage of the lock pin.

  1. A116229E01
    Remove the flange bolt and remove the camshaft timing gear assembly.

    NOTICE:
    1. Do not remove the other 4 bolts.
    2. When reusing the camshaft timing gear, unlock the lock pin inside the camshaft timing gear first.

← REMOVAL (Aug 2005 – Dec 2005)INSPECTION (from Aug 2005) →