2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
3.
REMOVE FRONT WIPER ARM HEAD CAP
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.
4.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
5.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
6.
REMOVE HOOD TO COWL TOP SEAL
Disengage the 7 clips and remove the hood to cowl top seal.
7.
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)
Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.
Disconnect the washer hose.
Disengage the 11 claws and clip.
Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.
8.
REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)
Remove the 2 clips.
Disengage the 4 claws and remove the cowl top ventilator louver LH.
9.
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)
Disconnect the washer hose.
Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.
10.
REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)
Remove the clip.
Disengage the 4 claws and remove the cowl top ventilator louver LH.
11.
REMOVE FRONT WIPER MOTOR AND LINK
Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.
12.
REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2
Disengage the claw and remove cowl to register duct sub-assembly No. 2.
13.
REMOVE COWL TOP PANEL OUTER
Disengage the wire harness clamp.
Remove the 9 bolts and remove the cowl top panel outer.
14.
REMOVE BATTERY
15.
REMOVE BATTERY TRAY
16.
REMOVE FRONT WHEEL RH
17.
REMOVE ENGINE UNDER COVER RH
18.
REMOVE ENGINE UNDER COVER SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)
19.
DRAIN ENGINE OIL
20.
DRAIN ENGINE COOLANT
NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.
Loosen the radiator drain cock plug.
Remove the radiator cap sub-assembly.
Loosen the cylinder block drain cock plug, then drain the coolant.
21.
REMOVE CYLINDER HEAD COVER NO. 2
Remove the 4 nuts and cylinder head cover No. 2.
22.
REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE NO. 1
Disconnect fuel vapor feed hose No. 1 and fuel vapor feed hose No. 2 from the vacuum switching valve assembly.
Disconnect the vacuum switching valve assembly connector and wire harness clamp.
Disconnect ventilation hose No. 2.
Disconnect the wire harness clamp and mass air flow meter connector.
Loosen the hose clamp, unlock the air cleaner assembly clamp and remove air cleaner cap sub-assembly with air cleaner hose No. 1.
23.
DISCONNECT RADIATOR HOSE NO. 3
Disconnect radiator hose No. 3.
24.
DISCONNECT RESERVE TANK HOSE
Disconnect the reserve tank hose.
25.
REMOVE WATER FILLER SUB-ASSEMBLY
Separate radiator hose No. 1 from the cylinder head.
Remove the 2 nuts and remove the water filler sub-assembly.
26.
DISCONNECT WATER BY-PASS HOSE NO. 2
Disconnect water by-pass hose No. 2.
27.
DISCONNECT WATER BY-PASS HOSE
Disconnect the water by-pass hose.
28.
DISCONNECT THROTTLE WITH MOTOR BODY CONNECTOR
Separate the wire harness clamp.
Remove the nut and separate the throttle with motor body connector.
29.
DISCONNECT VENTILATION HOSE
Disconnect the ventilation hose.
30.
DISCONNECT UNION TO CONNECTOR TUBE HOSE
Disconnect the union to connector tube hose.
31.
REMOVE OIL LEVEL GAGE SUB-ASSEMBLY
32.
REMOVE INTAKE MANIFOLD
Separate the wire harness clamps shown in the illustration.
Remove the 3 bolts and 2 nuts and remove the intake manifold.
33.
REMOVE OIL LEVEL GAGE GUIDE
Remove the wire harness clamp and the bolt and remove the oil level gauge guide.
34.
DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the fuel pipe clamp.
Pinch the retainer of the fuel tube connector, then pull out the fuel tube connector to disconnect the fuel tube from the fuel delivery pipe sub-assembly.
NOTICE:
Remove any dirt and foreign matter from the fuel tube connector before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting as the fuel tube connector has the O-ring that seals the pipe.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected parts by covering them with vinyl bags after disconnecting the fuel tube.
If the fuel tube connector and pipe are stuck, push and pull to release them.
35.
DISCONNECT BOOSTER VACUUM TUBE
Disconnect the booster vacuum tube.
36.
DISCONNECT CAMSHAFT POSITION SENSOR CONNECTOR
Disconnect the camshaft position sensor connector.
37.
DISCONNECT ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR
Disconnect the engine coolant temperature sensor connector.
Place a wooden block on a jack underneath the engine.
Remove the 5 bolts and nut and remove the engine mounting insulator sub-assembly RH.
52.
REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY
Set cylinder No. 1 to TDC/compression.
Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump.
for Unleaded Gasoline Specification Vehicle: Check that the timing marks on the camshaft timing sprocket and the camshaft timing gear are all facing upward as shown in the illustration.
HINT:
If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.
for Leaded Gasoline Specification Vehicle: Check that both timing marks on the camshaft timing sprockets facing upward as shown in the illustration.
HINT:
If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.
Using 2 SSTs, loosen the bolt while holding the crankshaft damper sub-assembly.
SST
09213-14010
(91651-60865)
09330-00021
NOTICE:
Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.
Remove the SSTs and the bolt.
Remove the crankshaft damper sub-assembly.
53.
REMOVE CRANKSHAFT POSITION SENSOR
Disconnect the crankshaft position sensor connector.
Remove the bolt and remove the crankshaft position sensor.
Remove the 4 bolts and remove the transverse engine engine mounting bracket.
58.
REMOVE OIL PUMP ASSEMBLY
Remove the 15 bolts and the nut.
Using a screwdriver with its tip wrapped in protective tape, prize the oil pump assembly to remove it.
NOTICE:
Do not damage the contact surfaces of the oil pump assembly and oil pan sub-assembly.
Remove the 2 O-rings from the cylinder block and oil pan sub-assembly.
59.
REMOVE OIL PUMP SEAL
Using a screwdriver with its tip wrapped in protective tape, remove the oil pump seal.
60.
REMOVE CHAIN TENSIONER ASSEMBLY NO. 1
NOTICE:
Do not rotate the crankshaft with the chain tensioner removed.
When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40 ° from the TDC first.
Pull up the stopper plate and hold it with its lock released.
Unlock the plunger of the tensioner and push it in to the end.
Pull down the stopper plate with the plunger pushed to the end and lock the plunger.
Insert a 3 mm (0.12 in.) diameter bar into the hole in the stopper plate and lock the plunger.
Remove the 2 bolts and remove chain tensioner assembly No. 1.
61.
REMOVE CHAIN TENSIONER SLIPPER
Remove the chain tensioner slipper.
62.
REMOVE CHAIN VIBRATION DAMPER NO. 1
Remove the 2 bolts and remove chain vibration damper No. 1.
63.
REMOVE CHAIN SUB-ASSEMBLY
64.
REMOVE CAMSHAFT
NOTICE:
When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.
Using several steps, loosen and remove the 19 bearing cap bolts uniformly in the sequence shown in the illustration, and then remove camshaft bearing cap No. 1 and camshaft bearing cap No. 2.
NOTICE:
Loosen each bolt uniformly while keeping the camshaft level.
Remove the camshaft and camshaft No. 2.
65.
REMOVE CYLINDER HEAD SUB-ASSEMBLY
Using several steps, loosen and remove the 10 cylinder head bolts uniformly with an 8 mm bi-hexagon wrench in the sequence shown in the illustration. Remove the 10 cylinder head bolts and the plate washers.
NOTICE:
Do not drop the washers into the cylinder head.
Head warpage or cracking could result from removing the bolts in the wrong order.
66.
REMOVE CYLINDER HEAD GASKET
Remove the cylinder head gasket.
67.
REMOVE EXHAUST MANIFOLD HEAT INSULATOR NO. 1
Remove the 3 bolts and remove exhaust manifold heat insulator No. 1.
68.
REMOVE EXHAUST MANIFOLD
Remove the 3 bolts and 2 nuts and remove the exhaust manifold.
69.
REMOVE HARNESS BRACKET
Remove the bolt and remove the harness bracket.
70.
REMOVE BOOSTER VACUUM TUBE
Remove the 2 bolts and remove the booster vacuum tube.
71.
REMOVE CAMSHAFT POSITION SENSOR
Remove the bolt and remove the camshaft position sensor.
72.
REMOVE ENGINE COOLANT TEMPERATURE SENSOR
Using SST, remove the engine coolant temperature sensor connector.
SST
09817-33190
73.
REMOVE WATER BY-PASS HOSE
Remove the water by-pass hose.
74.
REMOVE HARNESS BRACKET
Remove the bolt and remove the harness bracket.
75.
REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY
Remove the 3 bolts and remove the fuel delivery pipe sub-assembly with 4 fuel injectors.
NOTICE:
Do not drop the fuel injectors when removing the fuel delivery pipe sub-assembly.
76.
REMOVE FUEL INJECTOR ASSEMMBLY
Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.