INSTALLATION
Removal / installation · Vehicles built from Jan 2006
Versions by build date: Aug 2005 – Dec 2005 from Jan 2006
| 1. INSTALL OIL PUMP ASSEMBLY |
![]() ![]() |
Install 2 new O-rings onto the 2 locations shown in the illustration.
Apply seal packing to the oil pump assembly, cylinder head and cylinder block as shown in the illustration.


- Seal packing:
- Water pump part No. 08826 - 00100 or the equivalent
- Other part No. 08826 - 00080 or the equivalent
- NOTICE:
- Remove any oil from the contact surfaces.
- Install the oil pump assembly within 3 minutes and tighten the bolts and nut within 15 minutes of applying the seal packing.
- Do not expose the seal to engine oil for at least 2 hours after the installation.
- Remove any oil from the contact surfaces.
Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.

Install the oil pump assembly with the 15 bolts and the nut. Tighten the bolts and nut uniformly in several steps.

- Torque:
- Bolt A:
- 32 N*m{ 326 kgf*cm , 24 ft.*lbf }
- Bolt B:
- 11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }
- Bolt C:
- 11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }
- Nut D:
- 24 N*m{ 245 kgf*cm , 18 ft.*lbf }
- Bolt E:
- 24 N*m{ 245 kgf*cm , 18 ft.*lbf }
- NOTICE:
- After installing the oil pump assembly, install the mounting bracket and water pump within 15 minutes.
- HINT:
- Each bolt length is as follows.
- A: 30 mm (1.181 in.)
- B: 35 mm (1.378 in.)
- C: 20 mm (0.787 in.)
- E: 14 to 20 mm (0.551 to 0.787 in.), Double ended bolt
| 2. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET |
![]() ![]() |
Install the transverse engine engine mounting bracket with the 4 bolts.
- Torque:
- 55 N*m{ 561 kgf*cm , 41 ft.*lbf }
| 3. INSTALL WATER PUMP ASSEMBLY |
![]() ![]() |
Install the water pump assembly through a new gasket with the 3 bolts and 2 nuts.
- Torque:
- 11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }
| 4. INSTALL WATER PUMP PULLEY |
Provisionally install the water pump pulley with the 3 bolts.
Using SST, hold the water pump pulley.

- SST
- 09960-10010
(09962-01000, 09963-00700)
Tighten the 3 bolts to the specified torque.
- Torque:
- 15 N*m{ 153 kgf*cm , 11 ft.*lbf }
| 5. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() ![]() |
Apply a light coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.
- NOTICE:
- Do not twist the O-ring.
Install the camshaft timing oil control valve assembly with the bolt.

- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
Connect the camshaft timing oil control valve assembly connector.

| 6. INSTALL CRANKSHAFT POSITION SENSOR |
![]() ![]() |
Apply a light coat of engine oil to the O-ring on the crankshaft position sensor.
Install the crankshaft position sensor with the bolt.
- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
- NOTICE:
- Do not twist the O-ring.
Connect the crankshaft position sensor connector.
| 7. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY |
Align the pin hole of the crankshaft damper with the pin and install the crankshaft damper sub-assembly.
Provisionally install the bolt.
Using 2 SSTs, tighten the bolt while holding the crankshaft damper sub-assembly.

- SST
- 09213-14010
(91651-60865)
09330-00021
- Torque:
- 128 N*m{ 1,305 kgf*cm , 95 ft.*lbf }
- NOTICE:
- Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.
| 8. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH (for Hatchback) |
![]() ![]() |
Install the engine mounting insulator sub-assembly RH with the 5 bolts and nut.
- Torque:
- 45 N*m{ 459 kgf*cm , 33 ft.*lbf } for bolt A
- 52 N*m{ 530 kgf*cm , 38 ft.*lbf } for bolt B and nut
| 9. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH (for Sedan) |
![]() ![]() |
Install the engine mounting insulator sub-assembly RH with the 5 bolts and nut.
- Torque:
- 52 N*m{ 530 kgf*cm , 38 ft.*lbf }
| 10. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for RHD) |
![]() ![]() |
Apply seal packing to the cylinder head as shown in the illustration.
- Seal Packing:
- Part No. 08826-00080 or the equivalent
- NOTICE:
- Remove any oil from the contact surface.
- Install the cylinder head cover sub-assembly within 3 minutes of applying the seal packing.
- Do not start the engine for at least 2 hours after the installation.
- Remove any oil from the contact surface.
Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.
Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.

- Torque:
- 10 N*m{ 102 kgf*cm , 7.0 ft.*lbf }
Connect the connector and wire harness clamp as shown in the illustration and connect the engine wire harness.

Connect the fuel injector connectors.

| 11. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for LHD) |
![]() ![]() |
Disconnect the fuel injector connectors.
Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.

Remove the bolt and remove the wire harness bracket.

Remove the 9 bolts, 2 nuts and 2 seal washers and remove the cylinder head cover sub-assembly.

| 12. INSTALL VENTILATION HOSE NO. 2 |
![]() ![]() |
Connect ventilation hose No. 2.
| 13. INSTALL VENTILATION HOSE |
![]() ![]() |
Connect the ventilation hose.
| 14. INSTALL IGNITION COIL NO. 1 |
![]() ![]() |
Install the 4 ignition coils with the 4 bolts.
- Torque:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
Connect the 4 ignition coil connectors.

| 15. INSTALL GENERATOR ASSEMBLY |
![]() ![]() |
Provisionally install the generator with fixing bolt B.
Provisionally install the fan belt adjusting slider with fan belt adjusting slider fixing bolts A and B, then move the generator toward the cylinder block and tighten bolt B.

- Torque:
- 11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }
Install the connector and wire harness clamp.

Install terminal B with the nut.
- Torque:
- 9.8 N*m{ 100 kgf*cm , 7.2 ft.*lbf }
Install the terminal cap.
| 16. INSTALL FAN AND GENERATOR V BELT |
Provisionally install the fan and generator V belt onto each pulley.
- NOTICE:
- Make sure that the V-belt is securely fitted into the rib groove of the pulley.
| 17. ADJUST FAN AND GENERATOR V BELT |
Insert an adjusting bar between the engine mounting bracket and generator assembly. Push the adjusting bar towards the vehicle front to adjust the generator V belt tension.

- NOTICE:
- Do not insert the adjusting bar between the camshaft timing oil control valve assembly and generator assembly. It could damage the camshaft timing oil control valve assembly.
First tighten bolt A, then tighten bolt B.

- Torque:
- 19 N*m{ 189 kgf*cm , 14 ft.*lbf } for bolt A
- 54 N*m{ 551 kgf*cm , 40 ft.*lbf } for bolt B
| 18. INSPECT FAN AND GENERATOR V BELT |
Check the V belt deflection and tension.

- Deflection:
Item
Specified Condition
New belt
7.0 to 8.5 mm (0.28 to 0.33 in)
Used belt
11 to 13 mm (0.43 to 0.51 in)
- Tension:
Item
Specified Condition
New belt
539 to 637 N (55 to 65 kg, 121 to 143 ld)
Used belt
245 to 392 N (25 to 40 kg, 55 to 88 ld)
- HINT:
- Check the V belt deflection at the specified point.
- Check the drive belt deflection at the specified point.
- When installing a new belt, set its tension to the specified value.
- When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.
- When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of each Used Belt specification.
- V-ribbed belt tension and deflection should be checked after 2 revolutions of engine cranking.
- When using a belt tension gauge, confirm its accuracy by using a master gauge first.
- Check the V belt deflection at the specified point.
| 19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 20. ADD ENGINE OIL |
| 21. ADD ENGINE COOLANT |
Tighten all the plugs.
Pour engine coolant into the radiator assembly until it overflows.
- Capacity:
- M/T 4.8 liters (5.1 USqts, 4.5 lmp. qts)
- A/T 4.7 liters (5.0 USqts, 4.4 lmp. qts)
- NOTICE:
- Do not substitute water for engine coolant.
- HINT:
- Use of improper engine coolant may damage the engine coolant system.
- Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Use of improper engine coolant may damage the engine coolant system.
Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.
Install the radiator cap sub-assembly securely.
Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.
Warm up the engine until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
Item
Manual air conditioning system
Automatic air conditioning system
Set control as follows
Fan speed - Any setting except "OFF"
Temperature - Toward WARM
Air conditioning switch "OFF"
Fan speed - Any setting except "OFF"
Temperature - To the highest temperature
Air conditioning switch "OFF"
"AUTO" switch "OFF"
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
Stop the engine and wait until the coolant cools down.
If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.
Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.
Visually check for engine coolant leakage.
| 22. CHECK ENGINE OIL LEVEL |
Warm up the engine, then stop the engine and wait for 5 minutes. Check that the engine oil level is between the low and full marks on the oil level gauge.
If the engine oil level is low, check for oil leakage and add engine oil up to the full level mark.- NOTICE:
- Do not add engine oil to above the full level mark.
| 23. CHECK FOR ENGINE OIL LEAKAGE |
| 24. CHECK FOR ENGINE COOLANT LEAKAGE |
- CAUTION:
- To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.
Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
| 25. INSTALL CYLINDER HEAD COVER NO. 2 |
![]() ![]() |
Tighten 2 A nuts, then 2 B nuts .
- Torque:
- 7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
| 26. INSTALL ENGINE UNDER COVER RH |
| 27. INSTALL FRONT WHEEL RH |
- Torque:
- 103 N*m{ 1050 kgf*cm , 76 ft.*lbf }













