2005-2008 Yaris · Service Manual BODY ELECTRICAL

ADJUSTMENT

Removal / installation · Vehicles built from Aug 2005


1. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


4. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


5. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


6. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


8. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


9. REMOVE WASHER NOZZLE

E114463
  1. Disconnect the washer hose.

  1. Disengage the 2 claws and remove the front washer nozzle.

    NOTICE:
    Do not reuse the washer nozzle.


10. ADJUST WASHER NOZZLE

E108416E01
  1. Select a washer nozzle from the table so as to make the washer fluid hit within the specified area.

    Available Washer Nozzle:
    Part Number
    Discrimination Number
    Washer Fluid Injection Angle
    85381-52250
    12
    0°
    85381-52280
    13
    + 1°
    85381-52290
    11
    - 1°
    85381-52300
    14
    + 2°
    85381-52310
    10
    - 2°


11. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.


12. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


13. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


14. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


15. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


17. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


18. INSTALL FRONT WIPER ARM HEAD CAP

E113849
  1. Engage the claw and install the 2 front wiper arm head caps.

← ON-VEHICLE INSPECTION (from Aug 2005)PRECAUTION (from Aug 2005) →