2005-2008 Yaris · Service Manual BODY ELECTRICAL

ADJUSTMENT

Removal / installation · Vehicles built from Jan 2006


1. REMOVE FRONT WIPER ARM HEAD CAP

  1. E127832E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E127833
    Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.


3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


4. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH

  1. E127834E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.


5. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

  1. E127835
    Disengage the 2 clips, the 6 claws and the 10 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.

  1. E127836
    Disconnect the washer hoses.

  1. Disengage the 5 hooks.


7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

  1. E127838
    Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.

  1. E127839
    Disconnect the washer hoses.

  1. Disengage the 5 hooks.


8. REMOVE WASHER NOZZLE

E127796
  1. Disconnect the washer hose.

  1. Disengage the 2 claws and remove the front washer nozzle.

    NOTICE:
    Do not reuse the washer nozzle.


9. ADJUST WASHER NOZZLE

E108416E01
  1. Select a washer nozzle from the table so as to make the washer fluid hit within the specified area.

    Available Washer Nozzle:
    Part Number
    Discrimination Number
    Washer Fluid Injection Angle
    85381-52250
    12
    0°
    85381-52280
    13
    + 1°
    85381-52290
    11
    - 1°
    85381-52300
    14
    + 2°
    85381-52310
    10
    - 2°


10. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

  1. E127836
    Connect the washer hoses.

  1. Engage the 5 hooks.

  1. E127835
    Engage the 10 hooks and the 6 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.


11. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

  1. E127839
    Connect the washer hoses.

  1. Engage the 5 hooks.

  1. E127838
    Engage the 8 hooks and the 4 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 3 clips.


12. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH

  1. E129651
    Engage the 3 claws and install the cowl side ventilator sub-assembly LH.


13. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


14. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E129694E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


16. INSTALL FRONT WIPER ARM HEAD CAP

  1. E127841
    Engage the claw and install the 2 front wiper arm head caps.

← ON-VEHICLE INSPECTION (from Jan 2006)ON-VEHICLE INSPECTION (from Aug 2005) →