INSTALLATION
Removal / installation · Vehicles built from Nov 2005
Versions by build date: Aug 2005 – Oct 2005 from Nov 2005
| 1. CLEAN BACK DOOR GLASS |
![]() ![]() |
Using a scraper, remove the clips, dam and adhesive sticking to the back door glass.
Clean the outer circumference of the back door glass with a non-residue solvent.
- NOTICE:
- Do not touch the back door glass surface after cleaning it.
- Even if using a new back door glass, clean the back door glass with a non-residue solvent.
- Do not touch the back door glass surface after cleaning it.
- HINT:
- Since the pin is for positioning the glass, there is no need to replace it with a new one when reusing the glass, even if damaged.
| 2. CLEAN VEHICLE BODY |
Clean and shape the contact surface of the vehicle body.

Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
- NOTICE:
- Do not damage the vehicle body.
- HINT:
- Leave as much adhesive on the vehicle body as possible.
Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.
- HINT:
- Clean the vehicle body even if all the adhesive has been removed.
| 3. INSTALL BACK WINDOW GLASS ADHESIVE DAM KIT |
Apply Primer G to the glass where the dams will be installed.
- NOTICE:
- Allow the primer to dry for 3 minutes or more.
- Throw away any leftover Primer G.
- Do not apply too much Primer G.
- Allow the primer to dry for 3 minutes or more.
Install 2 new back door glass adhesive dams as shown in the illustration.

- Specification:
Area
Measurement
a
4.2 mm (0.165 in.)
| 4. INSTALL BACK DOOR GLASS |
Position the back door glass.

Using suction cups, place the back door glass in the correct position.
Check that the whole contact surface of the back door glass rim is perfectly even.
Place matchmarks on the back door glass and vehicle body.
- NOTICE:
- Check that the stoppers are attached to the vehicle body correctly.
- HINT:
- When reusing the back door glass, check and correct the matchmark positions.
Using suction cups, remove the back door glass.
Using a brush, apply Primer M to the exposed part of the vehicle body.

- NOTICE:
- Allow the primer to dry for 3 minutes or more.
- Do not apply Primer M to the adhesive.
- Throw away any leftover Primer M.
- Do not apply too much Primer M.
- Allow the primer to dry for 3 minutes or more.
Using a brush or sponge, apply Primer G to the edge of the back door glass and contact surface.


- NOTICE:
- Allow the primer to dry for 3 minutes or more.
- Throw away any leftover Primer G.
- Do not apply too much Primer G.
- Allow the primer to dry for 3 minutes or more.
- HINT:
- If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.
- Specification:
Area
Measurement
a
6.9 mm (0.272 in.)
b
11.0 mm (0.433 in.)
c
26.7 mm (1.051 in.)
d
40.7 mm (1.602 in.)
Apply adhesive.
- Adhesive:
- Part No. 08850-00801 or the equivalent
Cut off the tip of the cartridge nozzle, as shown in the illustration.

- HINT:
- After cutting off the tip, use all adhesive within the time indicated in the table below.
- Usage time frame:
Temperature
Usage Time Frame
35°C (95°F)
15 minutes
20°C (68°F)
1 hour 40 minutes
5°C (41°F)
8 hours
Load the sealer gun with the cartridge.
Apply adhesive to the back door glass, as shown in the illustration.


- Specification:
Area
Measurement
a
12.0 mm (0.472 in.)
b
8.0 mm (0.315 in.)
c
13.5 mm (0.532 in.)
d
33.7 mm (1.327 in.)
Install the back door glass onto the vehicle body.

Using suction cups, position the back door glass so that the matchmarks are aligned. Press it in gently along the rim.
- NOTICE:
- Allow the primer to dry for 3 minutes or more.
- Check that the stoppers are attached to the vehicle body correctly.
- Check that the vehicle body and back door glass have a small gap between them.
- Allow the primer to dry for 3 minutes or more.
Gently press the front surface of the back door glass to ensure that the back door glass is securely fitted to the vehicle body.
Using a scraper, remove any excessive or protruding adhesive.

- HINT:
- Apply adhesive onto the back door glass rim.
- NOTICE:
- Do not to drive the vehicle within the time indicated in the table below.
- Minimum time :
Temperature
Minimum time prior to driving vehicle
35°C (95°F)
1 hour 30 minutes
20°C (68°F)
5 hours
5°C (41°F)
24 hours
| 5. CHECK FOR LEAKAGE AND REPAIR |
Conduct a leak test by applying water to the adhesive portions after the adhesive has completely hardened.
Seal any leakage with auto glass sealer.
| 6. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for TMC Made) |
![]() ![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Install the rear wiper arm into the position shown in the illustration with the nut.

- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
- HINT:
- Hold the arm hinge down by hand while tightening the nut.
Close the rear wiper arm head cap.

| 7. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for TMMF Made) |
![]() ![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Install the rear wiper arm into the position shown in the illustration with the nut.

- Torque:
- 15 N*m{ 153 kgf*cm , 11 ft.*lbf }
- HINT:
- Hold the arm hinge down by hand while tightening the nut.
Close the rear wiper arm head cap.

| 8. INSTALL CENTER STOP LIGHT COVER |
![]() ![]() |
Connect the connector.
Engage the 2 claws.
Install the center stop light cover with the 2 screws.

- NOTICE:
- When reusing the center stop light cover, replace the screws with 90159-60303 screws to avoid insecure installation.
Engage the 4 claws and install the rear light cover.

| 9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



