ECM Power Source Circuit
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
When the ignition switch is turned on (IG), the battery voltage is applied to the IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the integration relay (EFI relay) and supplying power to either terminal +B or +B2 of the ECM.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT INTEGRATION RELAY (INTEGRATION RELAY - BODY GROUND) |
Remove the integration relay from the engine room relay block.

Measure the voltage between the terminal of the integration relay and the body ground.
- Standard voltage:
Tester Connections
Specified Conditions
Engine room relay block
(1C-1) - Body ground
9 to 14 V
Reinstall the integration relay.
|
|
||||
| OK | |
| 2. INSPECT INTEGRATION RELAY (EFI RELAY AND IG2 RELAY) |
![]() ![]() |
Remove the integration relay from the engine room relay block.
Inspect the EFI fuse and the AM2 fuse.
Remove the EFI fuse and AM2 fuse from the integration relay.
Check the EFI fuse and AM2 fuse resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the EFI fuse and the AM2 fuse.
Inspect the EFI relay and the IG2 relay.
Check the resistance between the terminals shown below.
- Standard resistance:
Tester Connections
Specified Conditions
1C-1 - 1A-4
10 kΩ or higher
Below 1 Ω
(when battery voltage is applied to terminals 1A-2 and 1A-3)
1C-1 - 1B-4
10 kΩ or higher
Below 1 Ω
(when battery voltage is applied to terminals 1A-2 and 1A-3)
1C-1 - 1B-1
Below 1 Ω
Reinstall the integration relay.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT) |
Check the harness and the connectors between the integration relay and the ECM.

Remove the integration relay from the engine room relay block.
Disconnect the A21 ECM connector.
Check the resistance.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
MREL (A21-44) - Engine room relay block (1A-2)
Below 1 Ω
+B (A21-2) - Engine room relay block (1A-4)
+B2 (A21-1) - Engine room relay block (1A-4)
- Standard resistance (Check for short):
Tester Connections
Specified Conditions
MREL (A21-44) or Engine room relay block (1A-2) - Body ground
10 kΩ or higher
+B (A21-2) or Engine room relay block (1A-4) - Body ground
+B2 (A21-1) or Engine room relay block (1A-4) - Body ground
Check the harness and the connectors between the integration relay and the body ground.
Check the resistance.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
Engine room relay block (1A-3) - Body ground
Below 1 Ω
Reinstall the integration relay.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
Disconnect the C20 ECM connector.

Check the resistance.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
E1 (C20-104) - Body ground
Below 1 Ω
Reconnect the ECM connector.
|
|
||||
| OK | |
| 5. INSPECT ECM (IGSW VOLTAGE) |
Disconnect the C20 and A21 ECM connectors.

Turn the ignition switch on (IG).
Measure the voltage between the terminals of the C20 and A21 ECM connectors.
- Standard voltage:
Tester Connections
Specified Conditions
IGSW (A21-28) - E1 (C20-104)
9 to 14 V
Reconnect the ECM connectors.
|
|
||||
| NG | |
| 6. INSPECT FUSE (IGN FUSE) |
![]() ![]() |
Remove the IGN fuse from the main body ECU.
Check the IGN fuse resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the IGN fuse.
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND) |
![]() ![]() |
Remove the integration relay from the engine room relay block.
Disconnect the A21 ECM connector.
Check the resistance.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
Engine room relay block (1B-4) - IGSW (A21-28)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connections
Specified Conditions
Engine room relay block (1B-4) or IGSW (A21-28) - Body ground
10 kΩ or higher
Reinstall the integration relay.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - IGNITION SWITCH ASSEMBLY) |
![]() ![]() |
Check the harness and the connectors between the integration relay and the ignition switch.
Remove the integration relay from the engine room relay block.
Disconnect the D8 ignition switch connector.
Check the resistance.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
Engine room relay block (1B-2) - IG2 (D8-6)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connections
Specified Conditions
Engine room relay block (1B-2) or IG2 (D8-6) - Body ground
10 kΩ or higher
Check the harness and the connectors between the integration relay and the body ground.
Check the resistance.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
Engine room relay block (1B-3) - Body ground
Below 1 Ω
Reinstall the integration relay.
Reconnect the ignition switch connector.
|
|
||||
| OK | |
| 9. INSPECT IGNITION OR STARTER SWITCH ASSEMBLY |
![]() ![]() |
Disconnect the D8 ignition switch connector.
Check the resistance between the terminals shown below.
- Standard resistance:
Key Positions
Tester Connections
Specified Conditions
LOCK
-
10 kΩ or higher
ACC
2 - 4
Below 1 Ω
ON
1 - 2 - 4
5 - 6
START
1 - 3 - 4
5 - 6 - 7
Reconnect the ignition switch connector.
|
|
||||
| OK | ||
| ||





