2005-2008 Yaris · Service Manual BODY ELECTRICAL

INSPECTION

Inspection · Vehicles built from Aug 2005


INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

B118055E01
  1. Check the operation.

    1. Apply battery voltage to the front door lock and check the operation of the front door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 3
      Locks
      Battery positive (+) → Terminal 3
      Battery negative (-) → Terminal 4
      Unlocks

      If the result is not as specified, replace the front door lock.

  1. Check the resistance of the unlock detection switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Condition
      Specified Condition
      7 - 8
      Locked
      10 kΩ or higher
      7 - 8
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the front door lock.

  1. Check the operation of the double door lock motor.

    1. Apply battery voltage to the front door lock and check the operation of the double door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Set
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Unset

      If the result is not as specified, replace the front door lock.

    2. While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.
      If the result is not as specified, replace the front door lock.

  1. Check the resistance of the double lock position switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Posistion
      Specified Condition
      5 - 6
      Set
      Below 1 Ω
      5 - 6
      Unset
      10 kΩ or higher

      If the result is not as specified, replace the front door lock.


INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

B132175E02
  1. Check the operation.

    1. Apply battery voltage to the front door lock and check the operation of the front door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 2
      Locks
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 4
      Unlocks

      If the result is not as specified, replace the front door lock.

  1. except for RHD vehicle w/o entry and start system:
    Check the resistance of the unlock detection switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Condition
      Specified Condition
      7 - 8
      Locked
      10 kΩ or higher
      7 - 8
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the front door lock.

  1. B118059E01
    except for RHD vehicle w/ entry and start system:
    Check the resistance of the door lock and unlock switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Condition
      Specified Condition
      7 - 9
      Locked
      Below 1 Ω
      7 - 9
      Unlocked
      10 kΩ or higher
      7 - 10
      Locked
      10 kΩ or higher
      7 - 10
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the front door lock.


INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

  1. B118056E01
    Check the operation.

    1. Apply battery voltage to the front door lock and check the operation of the front door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Locks
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Unlocks

      If the result is not as specified, replace the front door lock.

  1. Check the resistance of the unlock detection switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Condition
      Specified Condition
      7 - 8
      Locked
      10 kΩ or higher
      7 - 8
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the front door lock.

  1. B118057E01
    Check the resistance of the door lock and unlock switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Condition
      Specified Condition
      6 - 8
      Locked
      Below 1 Ω
      6 - 8
      Unlocked
      10 kΩ or higher
      5 - 8
      Locked
      10 kΩ or higher
      5 - 8
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the front door lock.

  1. Check the operation of the double door lock motor.

    1. Apply battery voltage to the front door lock and check the operation of the double door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 3
      Set
      Battery positive (+) → Terminal 3
      Battery negative (-) → Terminal 4
      Unset

      If the result is not as specified, replace the front door lock.

    2. While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.
      If the result is not as specified, replace the front door lock.

  1. Check the resistance of the double lock position switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Position
      Specified Condition
      9 - 10
      Set
      Below 1 Ω
      9 - 10
      Unset
      10 kΩ or higher

      If the result is not as specified, replace the front door lock.


INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

B118058E01
  1. Check the operation.

    1. Apply battery voltage to the front door lock and check the operation of the front door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 3
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 3
      Unlock

      If the result is not as specified, replace the front door lock.

  1. except for LHD vehicle w/o entry and start system:
    Check the resistance of the unlock detection switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Condition
      Specified Condition
      7 - 8
      Locked
      10 kΩ or higher
      7 - 8
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the front door lock.

  1. B118060E01
    except for LHD vehicle w/ entry and start system:
    Check the resistance of door lock and unlock switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Condition
      Specified Condition
      6 - 8
      Locked
      Below 1 Ω
      6 - 8
      Unlocked
      10 kΩ or higher
      5 - 8
      Locked
      10 kΩ or higher
      5 - 8
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the front door lock.

← REMOVAL (from Aug 2005)INSTALLATION (from Aug 2005) →