2005-2008 Yaris · Service Manual BODY ELECTRICAL

INSPECTION

Inspection · Vehicles built from Aug 2005


INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

B079079E02
  1. Check the operation.

    1. Apply battery voltage to the rear door lock and check the operation of the door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Locks
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Unlocks

      If the result is not as specified, replace the rear door lock.

  1. Check the resistance of the position switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Condition
      Specified Condition
      5 - 6
      Locked
      10 kΩ or higher
      5 - 6
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the rear door lock.

  1. Check the operation of the double door lock motor.

    1. Apply battery voltage to the rear door lock and check the operation of the double door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 3
      Set
      Battery positive (+) → Terminal 3
      Battery negative (-) → Terminal 4
      Unset

      If the result is not as specified, replace the rear door lock.

    2. While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.
      If the result is not as specified, replace the rear door lock.

  1. Check the resistance of the double lock position switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Condition
      Specified Condition
      9 - 10
      Set
      Below 1 Ω
      9 - 10
      Unset
      10 kΩ or higher

      If the result is not as specified, replace the rear door lock.


INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

B107859E01
  1. Check the operation.

    1. Apply battery voltage to the rear door lock and check the operation of the door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Locks
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlocks

      If the result is not as specified, replace the rear door lock.


INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

B079080E02
  1. Check the operation.

    1. Apply battery voltage to the rear door lock and check the operation of the door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 3
      Locks
      Battery positive (+) → Terminal 3
      Battery negative (-) → Terminal 4
      Unlocks

      If the result is not as specified, replace the rear door lock.

  1. Check the resistance of the position switch.

    1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Door Lock Condition
      Specified Condition
      9 - 10
      Locked
      10 kΩ or higher
      9 - 10
      Unlocked
      Below 1 Ω

      If the result is not as specified, replace the rear door lock.

  1. Check the operation of the double door lock motor.

    1. Apply battery voltage to the rear door lock and check the operation of the double door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Set
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Unset

      If the result is not as specified, replace the rear door lock.

    2. While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.
      If the result is not as specified, replace the rear door lock.

  1. Check the resistance of the double lock position switch.
    Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Door Lock Condition
    Specified Condition
    5 - 6
    Set
    Below 1 Ω
    5 - 6
    Unset
    10 kΩ or higher

    If the result is not as specified, replace the rear door lock.


INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

B107858E01
  1. Check the operation.

    1. Apply battery voltage to the rear door lock and check the operation of the door lock motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Locks
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlocks

      If the result is not as specified, replace the rear door lock.

← REMOVAL (from Aug 2005)INSTALLATION (from Aug 2005) →