2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Aug 2005 – Dec 2005

Versions by build date: Aug 2005 – Dec 2005 from Jan 2006


1. INSTALL RADIATOR DRAIN COCK

A106592
  1. Install the radiator drain cock onto the radiator assembly.


2. INSTALL RADIATOR RESERVE TANK HOSE GROMMET

A104901
  1. Install the 2 radiator reserve tank hose grommets onto the radiator assembly.


3. INSTALL RADIATOR SUPPORT CUSHION

A104900
  1. Install the 2 radiator support cushions onto the radiator assembly.


4. INSTALL FAN SHROUD

A104899
  1. Engage the 2 claws and install the fan shroud.


5. INSTALL OIL COOLER OUTLET HOSE (for Automatic Transaxle)

A106603
  1. Install the oil cooler outlet hose with the clip.


6. INSTALL OIL COOLER INLET HOSE (for Automatic Transaxle)

A106602
  1. Install the oil cooler inlet hose with the clip.


7. INSTALL RADIATOR HOSE NO. 2

A104898
  1. Install radiator hose No. 2 with the clip.


8. INSTALL RADIATOR ASSEMBLY (w/ Air Conditioning System)

A104897
  1. Engage the 2 claws and install the radiator assembly onto the vehicle.

    NOTICE:
    Do not apply excessive force to the cooler condenser assembly or piping when installing the radiator assembly.

  1. A104896
    Connect the cooling fan motor connector and wire harness clamp.


9. INSTALL RADIATOR ASSEMBLY (w/o Air Conditioning)

A104896
  1. Install the radiator assembly onto the vehicle.

  1. Connect the cooling fan motor connector and wire harness clamp.


10. CONNECT OIL COOLER OUTLET HOSE (for Automatic Transaxle)

A117307
  1. Connect the oil cooler outlet hose with the clip.


11. CONNECT OIL COOLER INLET HOSE (for Automatic Transaxle)

A117306
  1. Connect the oil cooler inlet hose with the clip.


12. CONNECT RADIATOR HOSE NO. 2

A104893
  1. Connect radiator hose No. 2 with the clip.


13. INSTALL RADIATOR HOSE NO. 3

A117310
  1. Install radiator hose No. 3 with the 2 clips.


14. CONNECT RADIATOR RESERVOIR TANK HOSE

A117356
  1. Connect the radiator reservoir tank hose to the water filler.


15. INSTALL RADIATOR SUPPORT SUB-ASSEMBLY UPPER

A104890
  1. Install the radiator support sub-assembly upper with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the horn assembly connector.


16. INSTALL HOOD LOCK ASSEMBLY

A104888
  1. Install the hood lock assembly with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. A104889
    Install the hood lock control cable assembly with the 2 clamps.


17. INSTALL COOLER COVER NO. 1 (w/ Air Conditioning System)

A109229
  1. Insert the 2 pins of cooler cover No. 1 into the radiator support LWR.

  1. Install cooler cover No. 1 with the 2 clips.


18. INSTALL RADIATOR SUPPORT ABSORBER UPPER

A104886E01
  1. Engage the 6 claws and install the radiator support absorber upper.


19. INSTALL AIR CLEANER ASSEMBLY

A104895
  1. Install the air cleaner case with air cleaner inlet No.1 with the 2 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Connect the wire harness to the air cleaner case.

  1. Install the air cleaner element.

  1. A117355
    Install and lock the air cleaner cap and air cleaner hose and then tighten the air cleaner hose clamp.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the ventilation hose to the air cleaner hose.

  1. Connect the vacuum switching valve connector and wire harness clamp.

  1. Connect the fuel vapor feed hose and fuel vapor feed hose No. 1 to the vacuum switching valve assembly.

  1. Connect the intake air flow meter connector and wire harness clamp.


20. INSTALL FRONT BUMPER COVER

  1. B119954
    w/ Front Spoiler:

    1. Install the 2 clips and the 4 screw grommets.

  1. B114362
    w/o Front Spoiler:

    1. Install the 2 clips and the screw grommet.

  1. w/ Fog Light:

    1. B117704
      Connect the 2 fog light connectors.

    2. Engage the 6 claws and install the front bumper cover.

  1. B117705
    w/o Fog Light:

    1. Engage the 6 claws and install the front bumper cover.

  1. B119955
    w/ Front Spoiler:

    1. Install the 7 clips.

    2. Install the 2 screw grommets.

    3. Tighten the 3 screws.

  1. B117706
    w/o Front Spoiler:

    1. Install the 7 clips.

    2. Install the 2 screw grommets.

    3. Tighten the 8 screws.

  1. B114359E01
    Remove the protective tape.


21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


22. ADD ENGINE COOLANT
  1. Tighten all the plugs.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    M/T 4.8 liters (5.1 USqts, 4.5 lmp. qts)
    A/T 4.7 liters (5.0 USqts, 4.4 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add the engine coolant.

  1. Visually check for engine coolant leakage.


23. ADJUST HOOD LOCK ASSEMBLY

B106964
  1. Loosen the 3 bolts.

  1. Adjust the hood lock position so that the striker can enter it smoothly.

  1. Tighten the 3 bolts after the adjustment.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


24. CHECK FOR ENGINE COOLANT LEAKAGE

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A106594
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.

← REMOVAL (from Jan 2006)INSTALLATION (from Jan 2006) →