Home › ENGINE › 1NZ-FE ENGINE MECHANICAL › ENGINE ASSEMBLY
REMOVAL
Removal / installation · Vehicles built Aug 2005 – Dec 2005
Versions by build date: Aug 2005 – Dec 2005 from Jan 2006
1.
DISCHARGE FUEL SYSTEM PRESSURE
Click here
2.
REMOVE BATTERY
Disconnect the cable from the battery terminal.
Loosen the nut and remove the battery clamp.
Remove the battery.
5.
REMOVE ENGINE UNDER COVER LH
6.
REMOVE ENGINE UNDER COVER RH
7.
DRAIN ENGINE COOLANT
NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.
Loosen the radiator drain cock plug.
Remove the radiator cap sub-assembly.
Loosen the cylinder block drain cock plug, then drain the coolant.
8.
DRAIN AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)
Remove the drain plug and gasket, and drain the ATF.
Install a new gasket and the drain plug.
Torque:
49 N*m{
500 kgf*cm
, 36 ft.*lbf
}
9.
REMOVE MANUAL TRANSAXLE OIL (for Manual Transaxle)
Stop the vehicle in a level place.
Remove the transmission filler plug and the gasket.
Check that the oil surface is within 5 mm (0.20 in.) of the bottom of the transmission filler plug opening.
NOTICE:
Excessively large or small amounts of oil may cause problems.
After replacing the oil, drive the vehicle and check the oil level again.
Check for oil leakage if the oil level is low.
Install the transmission filler plug and a new gasket.
Torque:
39 N*m{
400 kgf*cm
, 29 ft.*lbf
}
10.
REMOVE FRONT WIPER ARM HEAD CAP
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.
11.
REMOVE FRONT WIPER ARM RH
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
12.
REMOVE FRONT WIPER ARM LH
HINT:
Use the same procedure as for the RH side.
13.
REMOVE HOOD TO COWL TOP SEAL
Disengage the 7 clips and remove the hood to cowl top seal.
14.
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
Disconnect the washer hose.
Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.
15.
REMOVE COWL TOP VENTILATOR LOUVER LH
Remove the clip.
Disengage the 4 claws and remove the cowl top ventilator louver LH.
16.
REMOVE FRONT WIPER MOTOR AND LINK
Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.
17.
REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2
Disengage the claw and remove cowl to register duct sub-assembly No. 2.
18.
REMOVE COWL TOP PANEL OUTER
Disengage the wire harness clamp.
Remove the 9 bolts and remove the cowl top panel outer.
19.
REMOVE AIR CLEANER ASSEMBLY
Separate the intake air flow meter connector and wire harness clamp.
Separate the fuel vapor feed hose and fuel vapor feed hose No. 1 from the vacuum switching valve assembly.
Separate the vacuum switching valve connector and wire harness clamp.
Separate the ventilation hose from the air cleaner hose.
Release the air cleaner cap sub-assembly with air cleaner hose No. 1.
Loosen the air cleaner hose clamp on the throttle body side and remove the air cleaner cap and air cleaner hose.
Remove the air cleaner element.
Separate the wire harness clamp from the air cleaner case.
Remove the 2 bolts and remove the air cleaner case with air cleaner inlet No. 1.
20.
REMOVE AIR CLEANER BRACKET
Separate the wire harness clamp from the air cleaner bracket.
Remove the 2 bolts and remove the air cleaner bracket.
21.
REMOVE BATTERY CARRIER
Separate the wire harness clamp from the battery carrier.
Remove the 5 bolts and remove the battery carrier.
22.
DISCONNECT RADIATOR HOSE NO. 3
Disconnect radiator hose No. 3 from the water filler.
23.
DISCONNECT RADIATOR RESERVOIR TANK HOSE
Disconnect the radiator reservoir tank hose from the water filler.
24.
DISCONNECT RADIATOR HOSE NO. 2
Disconnect radiator hose No. 2 from the water inlet.
25.
DISCONNECT OIL COOLER INLET HOSE (for Automatic Transaxle)
Loosen the clip and disconnect the oil cooler inlet hose.
26.
DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transaxle)
Loosen the clip and disconnect the oil cooler outlet hose.
27.
REMOVE CYLINDER HEAD COVER NO. 2
Tighten 2 A nuts, then 2 B nuts .
Torque:
7.0 N*m{
71 kgf*cm
, 62 in.*lbf
}
28.
SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)
Remove the nut and disconnect the control cable from the control shaft lever.
Remove the clip and disconnect the control cable from the control cable bracket.
29.
SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
Remove the 2 clips and the 2 washers, and disconnect the 2 cables from the transaxle.
Remove the 2 clips and disconnect the 2 cables from the control cable bracket.
30.
DISCONNECT UNION TO CHECK VALVE HOSE
Disconnect the union to check valve hose from the booster vacuum tube.
31.
DISCONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)
Disconnect heater water outlet hose A from the heater unit.
32.
DISCONNECT HEATER WATER INLET HOSE A
Disconnect heater water inlet hose A from the heater unit.
33.
DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove fuel pipe clamp No. 1.
Pinch the retainer as illustrated, then pull the fuel tube connector out of the pipe.
NOTICE:
Remove any dirt and foreign matter from the fuel tube connector before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected parts by covering them with vinyl bags after disconnecting the fuel tube.
If the fuel tube connector and pipe are stuck, push and pull to release them.
34.
REMOVE FAN AND GENERATOR V BELT
Click here
35.
SEPARATE WITH PULLEY COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
Disconnect the connector.
Remove the 4 bolts and separate the with pulley compressor assembly.
HINT:
Remove the compressor assembly together with the low and high pressure hoses, then suspend them from the body with a piece of rope.
36.
SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)
Remove the 4 bolts, then separate the clutch release cylinder.
HINT:
Suspend the clutch release cylinder with a piece of rope so as not to overload the clutch pipe.
37.
DISCONNECT ENGINE WIRE
Pull up the lever and disconnect the connector of the engine control computer.
Remove the 2 connectors and clamp from the engine room junction block and disconnect the wire harness.
Remove the bolt and separate the transaxle earth wire of the engine room wire harness.
Disconnect all the wire harnesses and connectors. Make sure that no wire harness is connected between the body and engine.
38.
REMOVE COLUMN HOLE COVER SILENCER SHEET (for Automatic Transaxle)
Remove the floor carpet and 2 clips and remove the column hole cover silencer.
39.
REMOVE STEERING COLUMN HOLE COVER PLATE (for Manual Transaxle)
Remove the floor carpet and 2 clips and remove the column hole cover silencer.
40.
SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY
Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.
Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the power steering.
Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.
41.
SEPARATE STEERING COLUMN HOLE COVER SUB-ASSEMBLY NO. 1
Remove clip A, separate clip B from the body and separate steering column hole cover No. 1.
NOTICE:
Do not damage clip B.
42.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)
43.
REMOVE SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)
44.
REMOVE CONSOLE BOX REAR COVER
Disengage the 8 claws and remove the console box rear cover.
45.
REMOVE CONSOLE BOX ASSEMBLY REAR
Remove bolt <F>.
Disengage the 2 clips and remove the console box rear.
46.
REMOVE OXYGEN NO. 2 SENSOR
Disconnect the sensor connector.
Remove the grommet and pass the sensor connector out of the cabin through the floor panel.
Using SST, remove heated oxygen sensor No. 2.
SST
09224-00010
47.
REMOVE EXHAUST PIPE ASSEMBLY FRONT
Remove the 2 bolts and 2 springs and separate the exhaust tail pipe assembly.
Remove the 2 bolts and 2 springs and separate the exhaust manifold.
Remove the 3 exhaust pipe supports and remove the exhaust pipe assembly front.
48.
REMOVE FRONT AXLE SHAFT LH NUT
Using SST and a hammer, release the staked part of the axle hub nut.
SST
09930-00010
NOTICE:
Insert SST into the groove with the flat surface facing up.
Do not damage the tip of SST using grinders.
Completely unstake the staked part before removing the axle hub nut.
Do not damage the threads of the drive shaft.
Using a 30 mm socket wrench, remove the axle hub nut.
49.
REMOVE FRONT AXLE SHAFT RH NUT
HINT:
The removal procedure for the RH side is the same as that for the LH side.
50.
SEPARATE SPEED SENSOR FRONT LH
Remove the bolt and separate the speed sensor and flexible hose.
Remove the bolt and separate the speed sensor from the steering knuckle.
NOTICE:
Keep the speed sensor tip and installation portion free of foreign matter.
Remove the speed sensor without turning it from its original installation angle.
51.
SEPARATE SPEED SENSOR FRONT RH
HINT:
The separation procedure for the RH side is the same as that for the LH side.
52.
SEPARATE TIE ROD END SUB-ASSEMBLY LH
Remove the cotter pin and castle nut.
Using SST, separate the tie rod end from the steering knuckle.
SST
09628-62011
NOTICE:
Do not damage the tie rod end dust cover.
53.
SEPARATE TIE ROD END SUB-ASSEMBLY RH
HINT:
The separation procedure for the RH side is the same as that for the LH side.
54.
SEPARATE FRONT STABILIZER LINK ASSEMBLY LH
Remove the nut and separate the stabilizer link from the shock absorber.
HINT:
If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.
55.
SEPARATE FRONT STABILIZER LINK ASSEMBLY RH
HINT:
The separation procedure for the RH side is the same as that for the LH side.
56.
SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO. 1 LH
Remove the clip and castle nut.
Using SST, separate the lower arm.
SST
09628-00011
NOTICE:
Do not damage the lower ball joint dust cover.
Suspend SST with a piece of string or the equivalent.
57.
SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO. 1 RH
HINT:
The separation procedure for the RH side is the same as that for the LH side.
58.
SEPARATE FRONT AXLE ASSEMBLY LH
Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.
HINT:
If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.
Push the front axle out of the vehicle to remove the drive shaft from the front axle.
NOTICE:
Do not push the front axle further out of the vehicle than is necessary.
Do not damage the outboard joint boot.
Do not damage the speed sensor rotor.
Suspend the drive shaft with a piece of string or the equivalent.
59.
SEPARATE FRONT AXLE ASSEMBLY RH
HINT:
The separation procedure for the RH side is the same as that for the LH side.
60.
REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
Using SST, remove the drive shaft.
SST
09520-01010 09520-24010
(09520-32040)
NOTICE:
Do not damage the oil seal.
Do not damage the inboard joint boot.
Do not drop the drive shaft.
61.
REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
Using a screwdriver and hammer, remove the drive shaft.
NOTICE:
Do not damage the oil seal.
Do not damage the inboard joint boot.
Do not drop the drive shaft.
62.
REMOVE FLYWHEEL HOUSING UNDER COVER (for Automatic Transaxle)
63.
REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transaxle)
Remove the 6 torque converter set bolts.
64.
REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine lifter.
Remove the 5 bolts and nut and remove the engine mounting insulator RH.
Remove the through bolt and nut and separate the engine mounting insulator LH.
Remove the 6 bolts, and remove the engine assembly with transaxle and front suspension crossmember from the vehicle.
65.
REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Remove the bolt and remove the radio setting condenser.
Remove the bolt and remove the oxygen sensor wiring bracket.
Install the engine hangers with the bolts, as shown in the illustration.
Torque:
40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
Part No.: 12281-21010 for engine hanger 91642-81025 for bolt
Using an engine sling devise and a chain block, suspend the engine assembly with transaxle and front suspension crossmember.
Remove the through bolt from the engine moving control rod and remove the front suspension crossmember.
66.
REMOVE VENTILATION HOSE
Loosen the 2 clips and remove the ventilation hose.
67.
REMOVE VENTILATION HOSE NO. 2
Loosen the clips and remove ventilation hose No. 2.
68.
REMOVE FUEL TUBE SUB-ASSEMBLY
Disengage the claw and remove fuel pipe clamp No. 2.
Pinch the fuel tube connector retainer from both sides, disconnect the fuel tube connector and separate the fuel tube from the pipe.
NOTICE:
Remove any dirt and foreign matter from the fuel tube connector before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected parts by covering them with vinyl bags after disconnecting the fuel tube.
If the fuel tube connector and pipe are stuck, push and pull to release them.
69.
REMOVE WATER FILLER SUB-ASSEMBLY
Disconnect radiator hose No. 1 from the cylinder head.
Remove the 2 nuts and remove the water filler sub-assembly.
70.
REMOVE HEATER WATER INLET HOSE A
Disconnect heater water inlet hose A from the cylinder head.
71.
REMOVE FLYWHEEL HOUSING SIDE COVER
Disengage the claw by pushing it upward and remove the flywheel housing side cover.
72.
REMOVE STARTER ASSEMBLY
Remove the terminal cap.
Remove the nut and disconnect terminal 30.
Disconnect the connector.
Remove the 2 bolts and remove the starter assembly.
73.
REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)
Remove the 7 bolts and remove the automatic transaxle with torque converter.
74.
REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)
Hold the crankshaft with SST.
SST
09960-10010
(09962-01000, 09963-01000)
Remove the 6 bolts, drive plate spacer FR, drive plate and ring gear sub-assembly and drive plate spacer RR.
75.
REMOVE CONTROL CABLE BRACKET (for Manual Transaxle)
Remove the 2 bolts and the control cable bracket.
76.
REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)
Remove the 7 bolts and the manual transaxle.
77.
REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)
Align the matchmark on the clutch cover assembly with the one on the flywheel.
Loosen each set bolt one turn at a time until the spring tension is released.
Remove the set bolts and pull off the clutch cover.
NOTICE:
Do not drop the clutch disc.
78.
REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)
79.
REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
Hold the crankshaft with SST.
SST
09960-10010
(09962-01000, 09963-01000)
Remove the 6 bolts and flywheel.
80.
REMOVE IGNITION COIL NO. 1
Disconnect the connectors of the ignition coils.
Remove the bolt and remove all the ignition coils.
81.
REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY
82.
REMOVE GENERATOR ASSEMBLY
Remove the terminal cap.
Separate the connector and harness clamp.
Remove the nut and remove terminal B.
Remove fan belt adjusting slider fixing bolts A and B and remove the fan belt adjusting slider.
Remove fixing bolt B and remove the generator.
83.
REMOVE INTAKE MANIFOLD
Disconnect the union to connector tube hose from the booster vacuum tube.
Disconnect the engine wire from the intake manifold.
Disconnect the water bypass hose from the cylinder head.
Disconnect the water bypass hose from water bypass pipe No. 1.
Disconnect the throttle with motor body assembly connector.
Remove the 3 bolts and 2 nuts in the order shown in the illustration and remove the intake manifold.
Remove the gasket from the intake manifold.
84.
REMOVE WATER BY-PASS PIPE NO. 1
Remove the 2 bolts and 2 nuts and remove water bypass pipe No. 1.
85.
REMOVE BOOSTER VACUUM TUBE
Remove the 2 bolts and remove the booster vacuum tube.
86.
REMOVE ENGINE WIRE
Disconnect all sensor connectors and wire harness clamps from the engine assembly and remove the engine wire harness.
87.
REMOVE WIRE HARNESS CLAMP BRACKET
Remove the 2 bolts and remove the 2 wire harness clamp brackets.
88.
REMOVE EXHAUST MANIFOLD HEAT INSULATOR NO. 1
Remove the 4 bolts and remove the exhaust manifold heat insulator.
89.
REMOVE MANIFOLD SUPPORT BRACKET
Remove the 3 bolts and remove the manifold support bracket.
90.
REMOVE EXHAUST MANIFOLD
Remove the 3 bolts and 2 nuts and remove the exhaust manifold.
91.
REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
Remove the bolt and nut and remove the drive shaft heat insulator.