2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Jan 2006


1. INSTALL FRONT BRAKE FLEXIBLE HOSE

C116889E01
  1. Install the flexible hose with the union bolt and a new gasket.

    Torque:
    30 N*m{ 310 kgf*cm , 22 ft.*lbf }

    HINT:
    Install the flexible hose lock securely into the lock hole in the disc brake cylinder.

  1. w/ ABS:

    1. Install the flexible hose and speed sensor with the bolt.

      Torque:
      29 N*m{ 300 kgf*cm , 22 ft.*lbf }

      NOTICE:
      Install the flexible hose and speed sensor without twisting them.

  1. w/o ABS:

    1. Install the flexible hose with the bolt.

      Torque:
      29 N*m{ 300 kgf*cm , 22 ft.*lbf }

      NOTICE:
      Install the flexible hose without twisting it.

  1. Install a new clip.

  1. Using SST, install the brake tube.

    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.


2. FILL RESERVOIR WITH BRAKE FLUID

C133125E01
  1. Remove the cowl top No. 2 ventilator louver center.

  1. C133126E01
    Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4


3. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. C116910E01
    Using SST, disconnect the brake tubes from the master cylinder.
    SST
    09023-00100  

  1. C116911E01
    Slowly depress the brake pedal and hold it there (Step A).

  1. C116912E01
    Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.

  1. C116910E01
    Using SST, connect the brake tubes to the master cylinder.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.


4. BLEED BRAKE LINE

C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


5. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4


6. CHECK FOR BRAKE FLUID LEAKAGE

7. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }

← REMOVAL (from Jan 2006)COMPONENTS (from Aug 2005) →