INSTALLATION
Removal / installation · Vehicles built from Aug 2005
| 1. INSTALL FUEL INJECTOR ASSEMBLY |
![]() ![]() |
Apply a light coat of gasoline or spindle oil to new O-rings, then install one onto each fuel injector.
Apply a light coat of gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and the O-ring of the fuel injector.
While turning the fuel injector left and right, install it onto the fuel delivery pipe.

- NOTICE:
- Do not twist the O-ring.
- After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.
- Do not twist the O-ring.
| 2. INSTALL INJECTOR VIBRATION INSULATOR |
![]() ![]() |
Install 4 new injector vibration insulators onto the cylinder head.
| 3. INSTALL DELIVERY PIPE NO. 1 SPACER |
![]() ![]() |
Install the 2 No. 1 delivery pipe spacers onto the cylinder head.
- NOTICE:
- Install the delivery pipe No. 1 spacer in the correct direction.
| 4. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY |
![]() ![]() |
Install the fuel delivery pipe sub-assembly with the 4 fuel injectors, then provisionally install the 3 bolts.
- NOTICE:
- Do not drop the fuel injectors when installing the fuel delivery pipe sub-assembly.
- Check that the fuel injectors rotate smoothly after installing the fuel delivery pipe sub-assembly.
- Do not drop the fuel injectors when installing the fuel delivery pipe sub-assembly.
Tighten the 3 bolts to the specified torque.

- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf } for bolt A
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolt B
| 5. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() ![]() |
Insert the fuel tube connector into the fuel delivery pipe until a click sound can be heard.
- NOTICE:
- Check that there are no scratches or foreign matter around the disconnected parts of the fuel tube connector and pipe before performing this work.
- After connecting the fuel tube, check that the fuel tube connector and pipe are securely connected by pulling them.
- Check that there are no scratches or foreign matter around the disconnected parts of the fuel tube connector and pipe before performing this work.
Install the fuel pipe clamp.

| 6. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for RHD) |
![]() ![]() |
Apply seal packing to the cylinder head as shown in the illustration.
- Seal Packing:
- Part No. 08826-00080 or equivalent
- NOTICE:
- Remove any oil from the contact surface.
- Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.
- Do not start the engine within 2 hours of installation.
- Remove any oil from the contact surface.
Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.
Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.

- Torque:
- 10 N*m{ 102 kgf*cm , 7.0 ft.*lbf }
Connect the connector and wire harness clamp shown in the illustration and connect the engine wire harness.

Connect the fuel injector connectors.

| 7. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for LHD) |
![]() ![]() |
Apply seal packing to the cylinder head as shown in the illustration.
- Seal Packing:
- Part No. 08826-00080 or the equivalent
- NOTICE:
- Remove any oil from the contact surface.
- Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.
- Do not start the engine for at least 2 hours after installation.
- Remove any oil from the contact surface.
Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.
Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.

- Torque:
- 10 N*m{ 102 kgf*cm , 7.0 ft.*lbf }
Install the wire harness bracket with the bolt.

- Torque:
- 13 N*m{ 133 kgf*cm , 9.6 ft.*lbf }
Connect the connector and wire harness clamp shown in the illustration and connect the engine wire harness.

Connect the fuel injector connectors.

| 8. CONNECT VENTILATION HOSE NO. 2 |
![]() ![]() |
Connect ventilation hose No. 2.
| 9. CONNECT VENTILATION HOSE |
![]() ![]() |
Connect the ventilation hose.
| 10. INSTALL IGNITION COIL NO. 1 |
![]() ![]() |
Install the 4 ignition coils with the 4 bolts.
- Torque:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
Connect the 4 ignition coil connectors.

| 11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 12. CHECK FOR FUEL LEAKAGE |
When using the intelligent tester.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and intelligent tester main switch on.
- NOTICE:
- Do not start the engine.
Select the Active Test mode on the intelligent tester.
- HINT:
- Refer to the intelligent tester operator's manual for further details.
Check that there is no fuel leakage anywhere on the fuel system after doing maintenance.
| 13. CHECK FOR ENGINE OIL LEAKAGE |
| 14. INSTALL CYLINDER HEAD COVER NO. 2 |
![]() ![]() |
Tighten 2 A nuts, then 2 B nuts.
- Torque:
- 7.0 N*m{ 71 kgf*cm , 62 in.*lbf }










