2005-2008 Yaris · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. INSTALL INSTRUMENT CLUSTER FINISH PANEL SEAL

B108197
  1. Engage the 5 claws and install the panel seal.


2. INSTALL NO. 2 INSTRUMENT PANEL BOX

B108195
  1. Install the instrument panel box with the 2 <A> screws.


3. INSTALL NO. 1 INSTRUMENT PANEL BOX

B108196
  1. Install the instrument panel box with the 2 <A> screws.


4. INSTALL INSTRUMENT PANEL BOX SPRING

B108194
  1. Install the instrument panel box spring with screw <A>.


5. INSTALL FRONT PANEL SEAL

B108221
  1. Install the front panel seal.


6. INSTALL AIRBAG CUT OFF SWITCH CYLINDER

B108231
  1. Engage the 2 claws and install the airbag cut off switch cylinder.


7. INSTALL PUSH START SWITCH

B108224
  1. Engage the 2 claws and install the push start switch.


8. INSTALL HEADLIGHT LEVELING SWITCH

B108226
  1. Engage the 2 claws and install the headlight leveling switch.


9. INSTALL OUTER MIRROR SWITCH ASSEMBLY

B108225
  1. Engage the 2 claws and install the outer mirror switch.


10. INSTALL CIGARETTE LIGHTER INDICATOR LENS

  1. B119928
    Engage the 2 claws and install a new cigarette lighter indicator lens.


11. INSTALL CIGARETTE LIGHTER COVER

  1. B119924
    Engage the 2 claws and install the cigarette lighter cover.

  1. B119930
    Align the protrusion of the cigarette lighter socket with the cutout of the cigarette lighter indicator lens and install the cigarette lighter socket.

  1. Securely engage the claw.

  1. B119925
    Connect the cigarette lighter connector.


12. INSTALL CIGARETTE LIGHTER KNOB

  1. B119923
    Install the cigarette lighter knob.


13. INSTALL POWER OUTLET SOCKET COVER

  1. B117779
    Engage the 2 claws and install a new power outlet socket cover.


14. INSTALL POWER OUTLET SOCKET ASSEMBLY

  1. B117780
    Align the protrusion of the power outlet socket with the cutout of the power outlet socket cover and install the power outlet socket.

  1. Securely engage the claw.

  1. B117776
    Connect the power outlet connector.


15. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B108232E01
    Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. w/ Driver Side Knee Airbag

    1. Apply butyl tape to install a new instrument panel safety pad No. 1 onto the instrument panel lower (When installing a new one).

      Adhesive:
      Part No. 08850-00065, Butyl Tape Set or the equivalent

    2. Apply butyl tape to install a new instrument panel safety pad No. 2 onto the instrument panel lower (When installing a new one).

      Adhesive:
      Part No. 08850-00065, Butyl Tape Set or the equivalent

  1. Install the lower instrument panel with the 5 <D> bolts, 2 <E> bolts, screw <G> and screw <H>.

    NOTICE:
    Do not excessively tighten the <D> bolts, otherwise, it may damage the area not being tightened.

  1. Connect the clamps and connectors.

    B108193E01

  1. B108192
    Engage the 2 claws to connect the DLC3 connector.


16. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

B108191
  1. Engage the 3 claws to connect the control lever.


17. CONNECT ANTENNA CORD SUB-ASSEMBLY

B108200
  1. for LHD:

    1. Connect the 2 antenna cord clamps.

  1. B108160E01
    for RHD:

    1. Connect the 3 antenna cord clamps.


18. INSTALL NO. 6 HEATER TO REGISTER DUCT ASSEMBLY

B108190
  1. Engage the 4 claws and install the heater to register duct.


19. INSTALL INSTRUMENT PANEL BOX

B108189E01
  1. Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.

  1. Engage the 2 hinges with the instrument panel open.

  1. Close the instrument panel box.


20. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

21. INSTALL STEERING COLUMN COVER LOWER (w/ Driver Side Knee Airbag)

22. INSTALL STEERING COLUMN COVER SUPPORT (w/ Driver Side Knee Airbag)

23. INSTALL INSTRUMENT PANEL UNDER TRAY (w/o Driver Side Knee Airbag)

B108187
  1. Engage the 4 claws and install the instrument panel under tray.

  1. Install the 2 <A> screws.

  1. B108186
    Engage the 4 claws and install the instrument panel under tray.


24. INSTALL CONSOLE BOX ASSEMBLY REAR

B118993
  1. Engage the 2 clips and install the console box rear.

  1. Install bolt <F>.


25. INSTALL CONSOLE BOX CARPET

B118992
  1. Install the console box carpet.


26. INSTALL CONSOLE BOX REAR COVER

B118991
  1. Engage the 8 claws and install the console box rear cover.


27. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)

B118990
  1. Engage the 6 claws and install the shifting hole cover.


28. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

B118989
  1. Install the shift lever knob.


29. INSTALL COWL SIDE TRIM BOARD RH

  1. B114285
    Engage the claw and stud bolt and install the cowl side trim board.


30. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


31. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH

  1. B114572
    Engage the 3 claws and install the instrument panel under cover.

  1. Tighten the 2 screws.


32. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH

  1. B114571
    Engage the 4 claws and install the instrument panel under cover.


33. INSTALL FRONT DOOR SCUFF PLATE RH

  1. B114284
    Engage the 8 claws and install the front door scuff plate.


34. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


35. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

B108233E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the upper side of the instrument panel.

  1. Engage the claw and the 3 clips at the lower side of the instrument panel.

    B105355E01

  1. Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt

  1. Connect the connectors.

    B105354E01

  1. B108182
    Connect the passenger airbag connector and clamp.


36. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B105352
  1. Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.

  1. B108202
    Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.


37. INSTALL NO. 1 SWITCH HOLE BASE

B108201
  1. Disengage the 2 clips and 2 claws and install the switch hole base.


38. INSTALL FRONT PILLAR GARNISH RH

  1. B114342E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127672
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127674
      Connect the speaker connector.

  1. B114312
    Install the 3 antenna cord clamps.

  1. Connect the connector.

  1. w/ Curtain Shield Airbag:

    1. B117697E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B117694
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


39. INSTALL FRONT PILLAR GARNISH LH

  1. B114344E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127671
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127673
      Connect the speaker connector.

  1. B114316
    Install the 4 wire harness clamps.

  1. w/ Curtain Shield Airbag:

    1. B117698E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B114318
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


40. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.


41. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.


42. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

I101169
  1. Connect the 2 connectors and the aspirator pipe and engage the clamp.

  1. I101591
    Engage the 3 clips and 2 claws and install the air conditioner control.


43. CONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

I101159
  1. Engage the 2 claws and connect the air inlet damper control cable.


44. CONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

I101158
  1. Engage the 2 claws and connect the defroster damper control cable.


45. CONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY (for Manual Air Conditioning System)

I101157
  1. Engage the 2 claws and connect the air mix control cable clamp.

  1. Connect the defroster damper control cable to the clamp.


46. INSTALL AIR CONDITIONER PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

I101156
  1. Connect the 3 connectors and the clamp.

  1. I101155
    Engage the 3 clips and 2 claws and install the air conditioning panel.


47. INSTALL RADIO TUNER OPENING COVER (w/o Radio Receiver)

B108169
  1. Install the radio tuner opening cover with the 4 bolts.


48. INSTALL RADIO RECEIVER ASSEMBLY

E116762
  1. w/ Cassette Tape Player:

    1. Connect the connectors.

    2. Install the radio receiver with the 4 screws.

  1. I101590
    w/ CD Player:

    1. Connect the connectors.

    2. Engage the 4 clips and 2 claws and install the radio receiver.

    3. Install the 4 screws.


49. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER (Except CD Player)

E116764
  1. Engage the 4 clips and 2 claws and install the instrument cluster finish panel.


50. INSTALL COMBINATION METER ASSEMBLY

E107730
  1. Install the combination meter assembly with the 2 screws.

  1. Connect the 2 connectors.


51. INSTALL INSTRUMENT CLUSTER FINISH PANEL

B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. B132367
    Engage the 4 claws and 5 clips and install the instrument cluster finish panel.


52. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

E107743
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.

  1. E107744
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.


53. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

E107741
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.

  1. E107742
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.


54. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


55. CHECK SRS WARNING LIGHT
(Click here)
← REMOVAL (from Aug 2005)COMPONENTS (from Jan 2006) →