ON-VEHICLE INSPECTION
Inspection · Vehicles built from Aug 2005
- HINT:
- In this section, the terms Cold and Hot refer to the temperature of the coils. Cold means approximately -10 to 50 °C (14 to 122 °F). Hot means approximately 50 to 100 °C (122 to 212 °F).
| INSPECT IGNITION COIL AND SPARK TEST |
Check for DTCs.
- NOTICE:
- If a DTC is present, perform troubleshooting in accordance with the procedure for that DTC.
Check whether sparks occur.
Remove cylinder head cover No. 2 (Click here).
Remove the 4 ignition coils (Click here).
Using a 16 mm (0.63 in) plug wrench, remove the 4 spark plugs.
Install the spark plug onto each ignition coil and connect the ignition coil connectors.
Disconnect the 4 injector connectors.
Ground the spark plugs.
Check that sparks occur while the engine is being cranked.
- NOTICE:
- Ground the spark plug when checking.
- Replace the ignition coil when it has been subjected to a physical impact.
- Do not crank the engine for more than 2 seconds.
- Ground the spark plug when checking.
Perform the spark test in accordance with the following procedure.
Check that the wire harness side connector of the ignition coil with igniter is securely connected.
- Result:
Result
Proceed to
NG
Connect securely
OK
Go to next step
Perform a spark test on each ignition coil with igniter.
- Replace the ignition coil with igniter with a functioning one.
- Perform the spark test again.
- Result:
Result
Proceed to
OK
Replace ignition coil with igniter
NG
Go to next step
- Replace the ignition coil with igniter with a functioning one.
Check the power supply to ignition coil with igniter.
- Turn the engine switch on (IG).
- Check that there is battery voltage at ignition coil positive (+) terminal (Click here).
- Result:
Result
Proceed to
NG
Check wiring between engine switch and ignition coil with igniter
OK
Go to next step
- Turn the engine switch on (IG).
Check the resistance of camshaft position sensor.
- Standard resistance:
Temperature
Specified Condition
Cold
1,630 to 2,740 Ω
Hot
2,065 to 3,225 Ω
- Result:
Result
Proceed to
NG
Replace camshaft position sensor
OK
Go to next step
Check the resistance of the crankshaft position sensor.
- Standard resistance:
Temperature
Specified Condition
Cold
985 to 1,600 Ω
Hot
1,265 to 1,890 Ω
- Result:
Result
Proceed to
NG
Replace crankshaft position sensor
OK
Go to next step
Check the IGT from the ECM (Click here).
- Result:
Result
Proceed to
NG
Check ECM
OK
Repair wiring between ignition coil and ECM
Connect the 4 injector connectors.
Using a 16 mm (0.63 in) plug wrench, install the 4 spark plugs.
- Torque:
- 18 N*m{ 184 kgf*cm , 13 ft.*lbf }
Install the 4 ignition coils (Click here).
Install cylinder head cover No. 2 (Click here).
| INSPECT SPARK PLUG |
- NOTICE:
- Do not use a wire brush for cleaning.
Check the electrode.

Using a megaohmmeter, measure the insulation resistance.
- Standard resistance:
- 10 MΩ or more
- HINT:
- If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
- If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
- If a megaohmmeter is not available, perform the following simple inspection instead.
- If a megaohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method.
Quickly accelerate the engine to 4,000 rpm 5 times.
Remove the spark plug.
Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage on its thread and insulator.
If there is damage, replace the spark plug.- Recommended spark plug:
Manufacturer
Product
DENSO
K16R-U 11
NGK
BKR5EYA 11
Check the spark plug electrode gap.

- Maximum electrode gap for used spark plug:
- 1.3 mm (0.051 in.)
- Electrode gap for new spark plug:
- 1.0 to 1.1 mm (0.039 to 0.043 in.)
Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.- Air pressure:
- 588 kPa (6 kgf/cm2, 85 psi)
- Duration:
- 20 seconds or less
- HINT:
- Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.
