2005-2008 Yaris · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Aug 2005


INSPECT STARTER ASSEMBLY

NOTICE:
Perform each of the following tests within 3 to 5 seconds.

  1. Perform pull-in test.

    1. Disconnect the field coil lead wire from terminal C.

    2. A064944E01
      Connect the battery to the starter magnetic switch as shown in the illustration and check that the pinion gear is extended.

  1. A064945E01
    Perform holding test.

    1. Check that the pinion gear does not return inward after the cable of terminal C is disconnected.

  1. A064946E01
    Inspect the clutch pinion gear return.

    1. Move the pinion gear toward the armature.

  1. Perform operation test without load.

    1. Connect the field coil lead wire to terminal C.

      Torque:
      9.8 N*m{ 100 kgf*cm , 7.2 ft.*lbf }

    2. Clamp the starter in a vise.

    3. A117813E01
      Connect the battery and ammeter to the starter as shown in the illustration.

    4. Check that the ammeter indicates the specified current.

      Standard current:
      90A or less at 11.5 V


INSPECT STARTER ARMATURE ASSEMBLY

A104566E01
  1. Check the commutator for open circuits.

    1. Using an ohmmeter, check the resistance between the segments of the commutator.

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the starter armature assembly.

  1. A104565E01
    Check the commutator for ground.

    1. Using an ohmmeter, check the resistance between the commutator and armature core.

      Standard resistance:
      10 kΩor higher

      If the result is not as specified, replace the starter armature assembly.

  1. Check the commutator for dirt and burns on the surface.
    If the surface is dirty or burnt, restore it with sandpaper (No. 400) or a lathe.

  1. A037025
    Check for the commutator cirumference runout.

    1. Place the commutator on V-blocks.

    2. Using a dial indicator, measure the cirumference runout.

      Maximum runout:
      0.05 mm (0.0020 in.)

      If the runout is greater than the maximum, replace the starter armature assembly.

  1. A033574E01
    Using vernier calipers, measure the commutator diameter.

    Standard diameter:
    28.0 mm (1.1024 in.)

    Minimum diameter:
    27.0 mm (1.0630 in.)

    If the diameter is less than the minimum, replace the starter armature assembly.

  1. A033575E01
    Check that the undercut portion between the segments is free of foreign matter and measure its depth.

    Standard undercut depth:
    0.6 mm (0.0236 in.)

    Minimum undercut depth:
    0.2 mm (0.0079 in.)

    If the undercut depth is less than the minimum, correct it with a hacksaw blade.


INSPECT STARTER YOKE ASSEMBLY

A064787E01
  1. Using an ohmmeter, check the resistance between the terminal C and field coil brush lead.

    Standard resistance:
    Below 1 Ω

    If the result is not as specified, replace the starter yoke assembly.

  1. A064788E01
    Using an ohmmeter, check the resistance between the brush lead and starter yoke.

    Standard resistance:
    10 kΩor higher

    If the result is not as specified, replace the starter yoke assembly.


INSPECT BRUSH

A037017
  1. Using vernier calipers, measure the brush length.

    Standard length:
    14 mm (0.5511 in.)

    Minimum length:
    9 mm (0.3543 in.)

    If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

A037020E01
  1. Using an ohmmeter, measure the resistance between the positive (+) and negative (-) brush holders.

    Standard resistance:
    10 kΩor higher

    If the result is not as specified, replace the starter brush holder assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

A033579E01
  1. Hold the starter clutch and rotate the pinion gear clockwise, and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
    If necessary, replace the starter clutch sub-assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

A033580
  1. Check the plunger.

    1. Push in the plunger and check that it returns quickly to its original position.
      If necessary, replace the magnet starter switch assembly.

  1. A104569E01
    Check the pull-in coil for open circuits.

    1. Using an ohmmeter, check the resistance between terminals 50 and C.

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

  1. A104570E01
    Check whether the holding coil has open circuits.

    1. Using an ohmmeter, check the resistance between terminal 50 and the switch body.

      Standard resistance:
      Below 2 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

← DISASSEMBLY (from Aug 2005)REASSEMBLY (from Aug 2005) →