2005-2008 Yaris · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

C106362
  1. Install the control cable with the 3 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. C106359E01
    Install the control shift cable onto the shift lever retainer.

    NOTICE:
    1. Install the cable with the protruding portion of the cable outer facing upward.
    2. After installing, check that the lock of the cable outer is protruding beyond portion A, as shown in the illustration.

  1. Connect the control shift cable to the shift lever.

  1. Install the control shift cable onto the control cable bracket with a new clip.

  1. Connect the control shift cable and install the washer and clip.

  1. C106360E01
    Install the control select cable onto the shift lever retainer.

    NOTICE:
    1. Install the cable with the protruding portion of the cable outer facing upward.
    2. After installing, check that the lock of the cable outer is protruding beyond portion A, as shown in the illustration.

  1. C106361E01
    Connect the control select cable to the shift lever with the clip.

    NOTICE:
    1. Connect the control select cable so that the adjusting mechanism lock of the control select cable is installed on the left side of the vehicle.
    2. Insert the clip in the direction shown in the illustration.

  1. Install the control select cable onto the control cable bracket with a new clip.

  1. Connect the control select cable and install the washer and clip.

  1. C108468E02
    Adjust the length of the control select cable.

    1. Slide the adjuster case cover in the direction shown in the illustration (Illustration A).

    2. Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.

    3. Press the lock piece into the adjuster case and lock it (Illustration B).

    4. Slide the cover in the direction shown in the illustration (Illustration C).

      NOTICE:
      Slide the cover past the protrusion of the lock piece (Illustration D).


2. INSTALL FRONT FLOOR HEAT INSULATOR NO.1
  1. Install floor heat insulator No.1 with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


3. INSTALL EXHAUST PIPE ASSEMBLY FRONT

A104634
  1. Using vernier calipers, measure the free length of the compression spring.

    Minimum length (Front Side):
    40.5 mm (1.594 in.)
    Minimum length (Rear Side):
    38.5 mm (1.516 in.)

    If the length is not as specified, replace the compression spring.

  1. A104635E01
    Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Install the exhaust pipe gasket in the correct direction.
    2. Do not damage the outer surface of the exhaust pipe gasket.
    3. Do not reuse the exhaust pipe gasket.
    4. Do not push in the gasket with the exhaust pipe when connecting it.

  1. Install the 3 exhaust pipe support No. 4.

  1. Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

    A115439

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }


4. CONNECT OXYGEN SENSOR CONNECTOR

5. INSTALL CONSOLE BOX ASSEMBLY REAR

B118993
  1. Engage the 2 clips and install the console box rear.

  1. Install bolt <F>.


6. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

7. INSTALL BATTERY CARRIER

C106985
  1. Install the battery carrier with the 4 bolts.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }


8. INSTALL BATTERY TRAY

9. INSTALL BATTERY

10. INSTALL BATTERY CLAMP SUB-ASSEMBLY

11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Aug 2005)COMPONENTS (from Nov 2005) →