2005-2008 Yaris · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Aug 2005

HINT:
In this section, the terms cold and hot refer to the temperature of the coils. Cold means approximately -10 to 50°C (50 to 122°F). Hot means approximately 50 to 100°C (122 to 212°F).


PERFORM SPARK TEST
  1. Check for DTCs.

    NOTICE:
    If a DTC is present, perform troubleshooting procedure for that DTC.

  1. Check whether sparks occur.

    1. Remove the ignition coil (Click here).

    2. Remove the spark plug.

    3. Install the spark plug onto the ignition coil and connect the ignition coil connector.

    4. Disconnect the 3 injector connectors.

    5. Ground the spark plug.

    6. Visually check that sparks occur while the engine is being cranked.

      NOTICE:
      1. Ground the spark plugs when checking them.
      2. Replace the ignition coil if it has been stuck or dropped.
      3. Do not crank the engine for more than 2 seconds.

  1. Perform the spark test according to the procedure below.

    1. Check that the wire harness side connector of the ignition coil with igniter is securely connected.

      Result:
      Result
      Proceed to
      NG
      Connect securely
      OK
      Go to next step

    2. Perform a spark test on each ignition coil with igniter.

      1. Replace the ignition coil with igniter with a normally functioning one.
      2. Perform the spark test again.

        Result:
        Result
        Proceed to
        OK
        Replace ignition coil with igniter
        NG
        Go to next step

    3. Check the power supply to the ignition coil with igniter.

      1. Turn the Ignition Switch on (IG).
      2. Check that there is battery voltage at the ignition coil positive (+) terminal.

        Result:
        Result
        Proceed to
        NG
        Check wiring between engine switch and ignition coil with igniter
        OK
        Go to next step

    4. Check the resistance of the crankshaft position sensor.

      Standard resistance:
      1,850 to 2,450 Ω at 20°C (68°F)

      Result:
      Result
      Proceed to
      NG
      Replace crankshaft position sensor
      OK
      Go to next step

    5. Check the IGT signal from the ECM.

      Result:
      Result
      Proceed to
      NG
      Check ECM
      OK
      Repair wiring between ignition coil and ECM

  1. Using a 16 mm plug wrench, install the spark plug.

    Torque:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }

  1. Install the ignition coils (Click here).


INSPECT SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Do not attempt to adjust the electrode gap of a used spark plug.

  1. I039522E07
    Check the electron.

    1. Using a megaohmmeter, measure the insulation resistance.

      Standard resistance:
      10 MΩ or more

      If the resistance is less than the specified value, proceed to step (*3).

      HINT:
      If a megaohmmeter is not available, perform the following simple inspection instead.

  1. P003783
    Alternative inspection method:

    1. Quickly accelerate the engine to 4,000 rpm 5 times.

    2. Remove the spark plug.

    3. Visually check the spark plug.

    4. If the electron is dry, the spark plug is functioning. Proceed to step 2.

    5. If the electrode is damp, proceed to steps (*1), (*2) and (*3).

    6. Install the spark plug.

  1. Check the spark plug for any damage to its threads and insulator. (*1)
    If there is any damage, replace the spark plug.

    Recommended spark plug:
    Supplier
    Parts code
    DENSO
    K20HR-U11

  1. P003792
    Check the spark plug electrode gap. (*2)

    Maximum electrode gap for used spark plug:
    1.3 mm (0.051 in.)

    If the gap is greater than the maximum, replace the spark plug.

    Correct electrode gap for new spark plug:
    1.0 to 1.1 mm (0.039 to 0.043 in.)

    NOTICE:
    Bend only the base of the ground electrode when adjusting the gap of a new spark plug.

  1. B062019
    Clean the spark plugs. (*3)
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Air pressure:
    588 kPa (6 kgf/cm2, 85psi)

    Duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

← SYSTEM DIAGRAM (from Aug 2005)COMPONENTS (from Aug 2005) →