2005-2008 Yaris · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Nov 2006


1. INSTALL CLUTCH PEDAL STOPPER BOLT

C106356
  1. Install the clutch pedal stopper bolt and provisionally tighten the lock nut.

    HINT:
    Tighten the lock nut to the specified torque when adjusting the clutch pedal.


2. INSTALL CLUTCH START SWITCH ASSEMBLY

C106355
  1. Install the clutch start switch with the nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }


3. INSTALL CLUTCH PEDAL STOPPER

4. INSTALL CLUTCH PEDAL PAD
  1. Install the clutch pedal pad onto the clutch pedal.


5. INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH

C108471
  1. Apply MP grease to the inside of a new clevis bush.

  1. Install the new clevis bush onto the clutch pedal.

    HINT:
    Install the clevis bush from the right side of the vehicle.


6. INSTALL CLUTCH PEDAL NO.1 CUSHION

C106354
  1. Install the clutch pedal No. 1 cushion onto the clutch pedal.


7. INSTALL CLUTCH PEDAL SHAFT COLLAR

C106353
  1. Apply MP grease to both sides of the 2 bushes and collar.

  1. Install the 2 bushes and collar onto the clutch pedal.


8. INSTALL CLUTCH PEDAL SUB-ASSEMBLY

C106352
  1. Install the clutch pedal onto the clutch pedal support with the bolt and the nut.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


9. INSTALL SPRING HOLDER
  1. Install the spring holder onto the clutch pedal support.


10. INSTALL CLUTCH PEDAL SPRING

C158157
  1. Install the bush onto the clutch pedal.

  1. Apply MP grease to the contact surface of the spring holder, clutch pedal and spring.

  1. Install the spring onto the clutch pedal and spring holder.


11. INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

C106351
  1. Install the clutch pedal support onto the vehicle with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the clutch start switch connector.


12. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY

C106350
  1. Install the clutch master cylinder with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Apply MP grease to the contact surface of the hole pin and clevis bush.

  1. Connect the clevis to the clutch pedal with the hole pin.

    HINT:
    Install the hole pin from the right side of the vehicle.

  1. Install the clip onto the hole pin.


13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 47 in.*lbf }


14. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY
  1. Pull back the floor carpet.

  1. C106345E01
    Check that the pedal height is correct.

    Pedal height from floor:
    159.2 to 169.2 mm (6.268 to 6.661 in.)

  1. If the pedal height is not as specified, adjust it as follows.

    1. Loosen the lock nut and turn the stopper bolt until the correct height is obtained.

    2. Tighten the lock nut.

      Torque:
      16 N*m{ 160 kgf*cm , 12 ft.*lbf }


15. INSPECT CLUTCH START SWITCH ASSEMBLY

C115311
  1. Check that the engine does not start when the clutch pedal is released.

  1. Check that the engine starts when the clutch pedal is fully depressed.
    If necessary, replace the clutch start switch assembly.


16. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

  1. B114572
    Engage the 3 claws and install the instrument panel under cover.

  1. Tighten the 2 screws.

← REMOVAL (from Nov 2006)COMPONENTS (from Nov 2005) →