2005-2008 Yaris · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Jan 2006


1. INSTALL FRONT BUMPER ARM SUB-ASSEMBLY LH

  1. B134820
    Insert the 2 location pins into the 2 body holes and install the front bumper arm with the 4 bolts.

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }


2. INSTALL FRONT BUMPER ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


3. INSTALL WINDSHIELD WASHER JAR ASSEMBLY

  1. B134819
    Insert the location pin into the body hole and install the windshield washer jar with the 2 bolts.

    Torque:
    5.5 N*m{ 55 kgf*cm , 49 in.*lbf }


4. INSTALL HEADLIGHT ASSEMBLY

HINT:
Use the same procedure as for the LH side (Click here).


5. INSTALL FRONT BUMPER STONE DEFLECTOR BRACKET

B134818

HINT:
Use the same procedure for both sides.

  1. Install the front bumper stone deflector bracket with the 2 nuts.

    Torque:
    5.5 N*m{ 55 kgf*cm , 49 in.*lbf }


6. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

  1. B134817
    for G. C. C. Countries:

    1. Install the front bumper reinforcement with the 4 nuts and 6 bolts.

      Torque:
      5.5 N*m{ 55 kgf*cm , 49 in.*lbf } for nut
      40 N*m{ 410 kgf*cm , 30 ft.*lbf } for bolt

  1. B134816
    except G. C. C. Countries:

    1. Install the front bumper reinforcement with the 4 nuts and 6 bolts.

      Torque:
      5.5 N*m{ 55 kgf*cm , 49 in.*lbf } for nut
      40 N*m{ 410 kgf*cm , 30 ft.*lbf } for bolt


7. INSTALL NO. 2 ENGINE ROOM WIRE

  1. B134815
    w/ Fog Light:

    1. Install the No. 2 engine room wire with the 7 clamps.

  1. B134814
    w/o Fog Light:

    1. Install the No. 2 engine room wire with the 6 clamps.


8. INSTALL RADIATOR SUPPORT EXTENSION LH (w/ Radiator Support Extension)

  1. B134812
    Engage the 2 claws and install the radiator support extension.

  1. B138499
    w/o Air Conditioning System (LH Side Only):

    1. Install the clamp.


9. INSTALL RADIATOR SUPPORT EXTENSION RH (w/ Radiator Support Extension)

HINT:
Use the same procedure as for the LH side.


10. INSTALL RADIATOR SIDE AIR SEAL LH

  1. B134811
    for G. C. C. Countries:

    1. Engage the 4 claws and install the radiator side air seal.

    2. B138500
      w/ Air Conditioning System (LH Side Only):
      1. Install the clamp.

  1. B134810
    except G. C. C. Countries:

    1. Engage the 2 claws and install the radiator side air seal.


11. INSTALL RADIATOR SIDE AIR SEAL RH

HINT:
Use the same procedure as for the LH side.


12. INSTALL THERMISTOR ASSEMBLY (w/ Air Conditioning System)

  1. B134809
    Install the thermistor with the 2 clamps.


13. INSTALL RADIATOR SUPPORT UPPER ABSORBER

  1. B134808
    Engage the 6 claws and install the radiator support absorber.


14. INSTALL FRONT BUMPER SIDE RETAINER LH

  1. B134807
    Engage the 2 claws and install the front bumper side retainer.

  1. Tighten the screw and bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } for bolt


15. INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:
Use the same procedure as for the LH side.


16. INSTALL FRONT BUMPER COVER

  1. B134823
    Install the 2 clips and the screw grommet.

  1. B134801
    w/ Fog Light:

    1. Connect the 2 fog light connectors.

    2. Engage the 6 claws and install the front bumper cover.

  1. B134800
    w/o Fog Light:

    1. Engage the 6 claws and install the front bumper cover.

  1. B134805
    Install the 6 clips.

  1. Install the 2 screw grommets.

  1. Tighten the 7 screws and 3 bolts.

  1. B134799E01
    Remove the protective tape.


17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


18. PREPARE VEHICLE FOR HEADLIGHT AIMING ADJUSTMENT
  1. Prepare the vehicle:

    1. Ensure that there is no damage or deformation of the body around the headlights.
    2. Fill the fuel tank.
    3. Fill the oil to the specified level.
    4. Fill the coolant to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Place the spare tire, tools and jack in their original positions.
    7. Unload the trunk.
    8. Sit a person of average weight (75 kg, 165 lb) in the driver seat.


19. PREPARE FOR HEADLIGHT AIMING (for Using a Screen)

  1. E127797E01
    Prepare the following vehicle conditions:
    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Keep a 25 m (82 ft) distance between the center of the headlight bulb and the wall.
    4. Place the vehicle on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

      NOTICE:
      A distance of 25 m (82 ft) between the vehicle (the center of the headlight bulb) and the wall is necessary for proper aim adjustment. If unable to secure a distance of 25 m (82 ft), set a distance of exactly 3 m (9.84 ft) to check and adjust the headlight aim. (Since the target zone changes depending on the distance, follow the instructions shown in the illustration.)

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft) high x 4 m (13.1 ft) wide) to use as a screen.

  1. Draw a vertical line down the center of the screen (V line).

  1. Set the screen, as shown in the illustration.

    E127798E01

    HINT:
    1. Stand the screen perpendicular to the ground.
    2. Align the V line on the screen with the center of the vehicle.

  1. I033423E02
    Draw base lines (H line, V LH and V RH lines) on the screen, as shown in the illustration.

    HINT:
    1. The base lines differ for "low-beam inspection" and "high-beam inspection".
    2. Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb.


    1. H Line (Headlight height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low-beam headlights.

    2. V LH Line and V RH Line (Center mark positions of left-hand (LH) and right-hand (RH) headlights):
      Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low-beam headlight bulbs).


20. INSPECT HEADLIGHT AIMING
  1. Cover the headlight on the opposite side or disconnect its connector, to prevent light from the headlight not being inspected from affecting the headlight aiming inspection.

    NOTICE:
    Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, and may easily melt or be damaged due to heat.

  1. Start the engine.

    NOTICE:
    Engine rpm must be 1,500 or more.

  1. w/ Headlight leveling:
    Set the headlight leveling switch to 0 (zero).

  1. Turn on the headlight and make sure that the cutoff line falls within the specified area, as shown in the illustration.

    I041708E01

    HINT:
    1. Alignment distance is 25 m (82 ft):
      The cutoff line is 48 mm (1.88 in.) to 698 mm (27.48 in.) below the H line with low-beam (ECE Regulation No. 48).
    2. Alignment distance is 3 m (9.84 ft):
      The cutoff line is 6 mm (0.23 in.) to 84 mm (3.3 in.) below the H line with low-beam (ECE Regulation No. 48).
    3. Alignment distance is 25 m (82 ft):
      The cutoff line is 249 mm (9.8 in.) below the H line with low-beam.
    4. Alignment distance is 3 m (9.84 ft):
      The cutoff line is 30 mm (1.18 in.) below the H line with low-beam.
    5. Since the low-beam light and the high-beam light are a unit, if the aiming on one is correct, the other should also be correct. However, check both beams just to make sure.


21. ADJUST HEADLIGHT AIMING

  1. Adjust the aiming vertically:

    E127134E01
    Adjust the headlight aim to within the specified range by turning aiming screw A with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

  1. Perform low-beam aim adjustment.

    HINT:
    The headlight aim moves down when the aiming screw is turned clockwise, and moves up when the aiming screw is turned counterclockwise.

  1. Adjust the aim horizontally:
    Adjust the headlight aim to within the specified range by turning aiming screw B with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


22. PREPARE VEHICLE FOR FOG LIGHT AIMING ADJUSTMENT (w/ Fog Light)
  1. Prepare the vehicle:

    1. Ensure that there is no damage or deformation of the body around the fog lights.
    2. Fill the fuel tank.
    3. Fill the oil to the specified level.
    4. Fill the coolant to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Place the spare tire, tools and jack in their original positions.
    7. Unload the trunk.
    8. Sit a person of average weight (75 kg, 165 lb) in the driver seat.


23. PREPARE FOR FOG LIGHT AIMING (w/ Fog Light)

E127799E01
  1. Prepare the following vehicle conditions:

    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.
    2. Place the vehicle at a 90°angle to the wall.
    3. Keep a 7.62 m (25 ft) distance between the center of the fog light bulb and the wall.
    4. Place the vehicle on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

    NOTICE:
    A distance of 7.62 m (25 ft) between the vehicle (center of the fog light bulb) and the wall is necessary for proper aim adjustment. If unable to secure a distance of 7.62 m (25 ft), secure a distance of exactly 3 m (9.84 ft) to check and adjust the fog light aim. (Since the target zone will change with the distance, follow the instructions shown in the illustration.)

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft) high x 4 m (13.1 ft) wide) to use as a screen.

  1. Draw a vertical line down the center of the screen (V line).

  1. Set the screen as shown in the illustration.

    HINT:
    1. Stand the screen perpendicular to the ground.
    2. Align the V line on the screen with the center of the vehicle.


    E127800E01

  1. I033423E02
    Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.

    HINT:
    Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


    1. H Line (Fog light height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the low-beam fog lights.

    2. V LH Line and V RH Line (Center mark positions of left-hand (LH) and right-hand (RH) fog lights):
      Draw two vertical lines so that they intersect the H line at each center mark.


24. INSPECT FOG LIGHT AIMING (w/ Fog Light)
  1. Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light not being inspected from affecting fog light aiming inspection.

  1. Start the engine.

    NOTICE:
    Engine rpm must be 1,500 or more.

  1. Turn on the fog light and make sure that the cutoff line falls within the specified area, as shown in the illustration.

    I041221E03


25. ADJUST FOG LIGHT AIMING (w/ Fog Light)

E107962
  1. Adjust the fog light aim to within the specified range by turning the aiming screw with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

← REASSEMBLY (from Jan 2006)COMPONENTS (from Aug 2005) →