TERMINALS OF ECU
System information · Vehicles built from Aug 2005


| CHECK COMBINATION METER |
Disconnect the D1 combination meter assembly connector.
Measure the voltage and resistance of the wire harness side connector.
If the result is not as specified, there may be a malfunction in the wire harness.Standard: Symbols (Terminals No.)
Wiring Color
Terminal Description
Condition
Specified Condition
IG2 (D1-1) - Body ground
B - Body ground
Ignition switch signal
Ignition switch off→on (IG)
Below 1 V→10 to 14 V
ECU-B (D1-2) -
Body ground
L - Body ground
Battery
Always
10 to 14 V
ET (D1-24) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
Disconnect the D2 combination meter assembly connector.
Measure the voltage of the wire harness side connector.
*1: for EuropeStandard voltage: Symbols (Terminals No.)
Wiring Color
Terminal Description
Condition
Specified Condition
L (D1-3) - Body ground
V - Body ground
Fuel level signal
Ignition switch on (IG)
10 to 14V
TEMP *1 (D1-4) - Body ground
W - Body ground
Ambient temperature sensor signal
Ignition switch on (IG)
4.5 to 5.5V
TX+ *6 (D1-8) - Body ground
Y - Body ground
Multi-mode manual transmission ECU signal
Multi-mode manual transmission warning light ON→OFF
Below 1V→4.5 to 5.5V
P/SB (D1-10) - Body ground
O - Body ground
Seat belt condition signal (Passenger side)
Ignition switch on (IG)
P-BELT indicator light OFF→ON→OFF
Below 1 V→10 to 14 V
→Below 1 V
OILW (D1-11) - Body ground
O - Body ground
Oil level sensor signal
Ignition switch on (IG)
10 to 14V
BRQ *6 (D1-13) - Body ground
R - Body ground
Multi-mode manual transmission ECU signal
Multi-mode manual transmission warning light ON→OFF
Below 1V→4.5 to 5.5V
ILL+ *7 (D1-14) - Body ground
G - Body ground
Taillight signal
Light control switch OFF→ON
Below 1 V→10 to 14 V
+S (D1-16) - Body ground
SB - Body ground
Speed signal (Output)
Driving at approximately
20 km/h (12 mph)
Pulse generation
(See waveform 1)
SI (D1-17) - Body ground
P - Body ground
Speed signal (Input)
Driving at approximately
20 km/h (12 mph)
Pulse generation
(See waveform 1)
CANH (D1-20) - Body ground
G - Body ground
CAN communication line
Ignition switch on (IG)
Pulse generation
CANL (D1-21) - Body ground
W - Body ground
CAN communication line
Ignition switch on (IG)
Pulse generation
TX1+ *1 (D1-23) - Body ground
B - Body ground
Ambient temperature sensor ground
Always
Below 1 Ω
CHG- *2 (D2-1) - Body ground
SB*4 or L*5 - Body ground
Charge warning light signal
Engine start
Charge warning light ON→OFF
Below 1V→10 to 14 V
B *3 (D2-1) - Body ground
LG - Body ground
Turn signal LH signal
Ignition switch on (IG)
Turn signal LH indicator light OFF→ON→OFF
Below 1 V→10 to 14 V
→Below 1 V
SW *9 (D2-2) - Body ground
V - Body ground
Brake fluid level warning light signal
Ignition switch on (IG)
Brake fluid level warning light ON→OFF
Below 1 V→10 to 14 V
FOG *3 (D2-2) - Body ground
R - Body ground
Front fog signal
Ignition switch on (IG)
Front fog switch OFF→ON
Below 1V→10 to 14 V
S *3 (D2-3) - Body ground
SB - Body ground
Rear fog signal
Ignition switch on (IG)
Rear fog switch OFF→ON
Below 1V→10 to 14 V
S *7 (D2-3) - Body ground
GR - Body ground
Fuel filter warning switch signal
Fuel filter warning light ON→OFF
Below 1 V→10 to 14 V
EFI *2 (D2-4) - Body ground
B - Body ground
Check engine warning light signal
Check engine warning light signal ON→OFF
Below 1V→10 to 14 V
EFI *3 (D2-5) - Body ground
B - Body ground
Check engine warning light signal
Check engine warning light signal ON→OFF
Below 1V→10 to 14 V
S *2 (D2-6) - Body ground
SB - Body ground
Rear fog signal
Ignition switch on (IG)
Rear fog switch OFF→ON
Below 1V→10 to 14 V
S *8 (D2-6) - Body ground
GR - Body ground
Fuel filter warning switch signal
Fuel filter warning light ON→OFF
Below 1 V→10 to 14 V
FOG *2 (D2-7) - Body ground
R - Body ground
Front fog signal
Ignition switch on (IG)
Front fog switch OFF→ON
Below 1V→10 to 14 V
SW *10 (D2-7) - Body ground
V - Body ground
Brake fluid level warning light signal
Brake fluid level warning light ON→OFF
Below 1V→10 to 14 V
B *2 (D2-8) - Body ground
LG - Body ground
Turn signal LH signal
Ignition switch on (IG)
Turn signal LH indicator light ON
Below 1V→10 to 14 V
→Below 1 V
CHG- *3 (D2-8) - Body ground
L - Body ground
Charge warning light signal
Engine start
Charge warning light ON→OFF
Below 1 V→10 to 14 V
PBLT *2 (D2-9) - Body ground
O - Body ground
Seat belt warning light signal (Passenger side)
Ignition switch on (IG)
Front passenger seat belt warning light OFF→ON→OFF
Below 1 V→10 to 14 V
→Below 1 V
IND *3 (D2-9) - Body ground
G - Body ground
Taillight indicator signal
Light control switch OFF→ON
Below 1 V→10 to 14 V
B *3 (D2-10) - Body ground
BR - Body ground
Turn signal RH signal
Ignition switch on (IG)
Turn signal RH indicator light OFF→ON→OFF
Below 1V→10 to 14 V
→Below 1 V
BEAM- *2 (D2-11) - Body ground
W-B *4- Body ground
HI-BEAM indicator signal (-)
BEAM indicator light ON→OFF
Below 1V→10 to 14 V
P *5 - Body ground
BEAM+ *3 (D2-11) - Body ground
GR - Body ground
HI-BEAM indicator signal (+)
Always
10 to 14 V
OIL P *2 (D2-12) - Body ground
Y - Body ground
Engine oil pressure signal
Engine oil pressure warning light ON→OFF
Below 1V→10 to 14 V
OIL P *3 (D2-13) - Body ground
Y - Body ground
Engine oil pressure signal
Engine oil pressure warning light ON→OFF
Below 1V→10 to 14 V
BEAM+ *2 (D2-14) - Body ground
GR - Body ground
HI-BEAM indicator signal (+)
Always
10 to 14 V
BEAM- *3 (D2-14) - Body ground
P - Body ground
HI-BEAM indicator signal (-)
BEAM indicator light ON→OFF
Below 1V→10 to 14 V
B *2 (D2-15) - Body ground
BR - Body ground
Turn signal RH signal
Ignition switch on (IG)
Turn signal RH indicator light OFF→ON→OFF
Below 1V→10 to 14 V
→Below 1 V
IND *2 (D2-16) - Body ground
G - Body ground
Tail light indicator signal
Headlight dimmer switch
(TAIL) OFF→ON
Below 1V→10 to 14 V
PBLT *3 (D2-16) - Body ground
O - Body ground
Seat belt warning light signal (Passenger side)
Ignition switch on (IG)
Front passenger seat belt warning light OFF→ON→OFF
Below 1V→10 to 14 V
→Below 1 V
*2: LHD (TMC & TMMF Made)
*3: RHD (TMC & TMMF Made)
*4: w/ Daytime running light
*5: w/o Daytime running light
*6: for MMT
*7: LHD (for 1ND-TV)
*8: RHD (for 1ND-TV)
*9: LHD (TMC Made only)
*10: RHD (TMC Made only)
If the result is not as specified, the combination meter assembly may have a malfunction.
Waveform 1: Using an oscilloscope

Terminal Connections
+S (D1-16) and Body ground
SI (D1-17) and Body ground
Tester Range
5V/DIV, 20ms/DIV
Vehicle Condition
Driving at approximately 20km/h (12mph)
- HINT:
- As the vehicle speed increases, the cycle of the signal waveform narrows.
Reconnect the combination meter assembly connectors.
| CHECK MAIN BODY ECU (w/ ENTRY AND START SYSTEM) |




| Symbols (Terminals No.) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| RRCY (4A-5) - GND1 (4E-17) |
G - W-B |
Rear door courtesy switch signal (LH) |
Rear door (LH) CLOSED→ OPEN |
10 to 14 V→Below 1 V |
| BCTY (4A-7) - GND1 (4E-17) |
SB - W-B |
Back door courtesy switch signal |
Back door CLOSED→ OPEN |
10 to 14 V→Below 1 V |
| RRCY (4A-20) - GND1 (4E-17) |
L - W-B |
Rear door courtesy switch signal (RH) |
Rear door (RH) CLOSED→ OPEN |
10 to 14 V→Below 1 V |
| DCTY (4A-21) - GND1 (4E-17) |
R - W-B |
Front door courtesy switch signal (Driver Side) |
Front door (Driver Side) CLOSED→ OPEN |
10 to 14 V→Below 1 V |
| PCTY (4A-24) - GND1 (4E-17) |
L - W-B |
Front door courtesy switch signal (Passenger Side) |
Front door (Passenger Side) CLOSED→OPEN |
10 to 14 V→Below 1 V |
| PKB (4C-2) - GND1 (4E-17) |
Y - W-B |
Parking brake signal |
Parking brake warning light ON→OFF |
10 to 14 V→Below 1 V |
| KSW (4D-7) - GND1 (4E-17) |
Y - W-B |
Key unlock warning switch input |
Key inserted→Removed |
10 to 14 V→Below 1 V |
| GND1 (4E-17) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
| CANH (D66-15) - Body ground |
R - Body ground |
CAN communication line |
Ignition switch on (IG) |
Pulse generation |
| CANL (D66-16) - Body ground |
W - Body ground |
CAN communication line |
Ignition switch on (IG) |
Pulse generation |
| DBKL (D64-26) - Body ground |
W - Body ground |
Seat belt condition signal (Driver side) |
Driver seat belt warning light OFF→ON |
10 to 14 V→Below 1 V |
| CHECK MAIN BODY ECU (w/o ENTRY AND START SYSTEM) |




| Symbols (Terminals No.) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| RRCY (4A-5) - GND1 (4E-17) |
G - W-B |
Rear door courtesy switch signal (LH) |
Rear door (LH) CLOSED→ OPEN |
10 to 14 V→Below 1 V |
| BTCY (4A-7) - GND1 (4E-17) |
SB - W-B |
Back door courtesy switch signal |
Back door CLOSED→ OPEN |
10 to 14 V→Below 1 V |
| RRCY (4A-20) - GND1 (4E-17) |
L - W-B |
Rear door courtesy switch signal (RH) |
Rear door (RH) CLOSED →OPEN |
10 to 14 V→Below 1 V |
| DCTY (4A-21) - GND1 (4E-17) |
R - W-B |
Front door courtesy switch signal (Driver Side) |
Front door (Driver Side) CLOSED →OPEN |
10 to 14 V→Below 1 V |
| PCTY (4A-24) - GND1 (4E-17) |
L - W-B |
Front door courtesy switch signal (Passenger Side) |
Front door (Passenger Side) CLOSED→OPEN |
10 to 14 V→Below 1 V |
| PKB (4C-2) - GND1 (4E-17) |
Y - W-B |
Parking brake signal |
Parking brake warning light ON→OFF |
10 to 14 V→Below 1 V |
| KSW (4D-7) - GND1 (4E-17) |
Y - W-B |
Key switch condition signal |
Key inserted→Removed |
10 to 14 V→Below 1 V |
| GND1 (4E-17) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
| CANL (D33-22) - Body ground |
W - Body ground |
CAN communication line |
Ignition switch on(IG) |
Pulse generation |
| CANH (D33-23) - Body ground |
R - Body ground |
CAN communication line |
Ignition switch on (IG) |
Pulse generation |
| DBKL(D33-9) - Body ground |
W - Body ground |
Seat belt condition signal (Driver side) |
Driver seat belt warning light OFF→ON |
10 to 14 V→Below 1 V |
| COMBINATION METER INTERNAL CIRCUIT |
*2: RHD
*3: w/ Daytime running light system
*4: w/o Daytime running light system
*5: for Europe
*6: w/ VSC
*7: w/ ABS
*8: for MMT
*9: for 1ND-TV
*10: for TMC Made






| Terminal No. |
Wire Harness Side |
|
| D1 |
1 |
Ignition switch |
| 2 |
Battery |
|
| 3 |
Fuel sender gauge assembly |
|
| 4 |
Ambient temperature sensor *5 |
|
| 8 |
Transmission control ECU assembly *8 |
|
| 10 |
Front seat inner belt assembly (Passenger side) |
|
| 11 |
Oil level sensor *9 |
|
| 13 |
Transmission control ECU assembly *8 |
|
| 14 |
T-LP relay *4, Daytime running light relay *3 |
|
| 16 |
ECM, Power steering ECU |
|
| 17 |
ABS and traction actuator *6, Brake actuator *7 |
|
| 20 |
CAN communication line |
|
| 21 |
CAN communication line |
|
| 23 |
Ambient temperature sensor *5 |
|
| 24 |
Body ground |
|
| D2 *1 |
1 |
Generator (Alternator) |
| 2 |
Brake fluid level warning switch *10 |
|
| 3 |
Fuel filter switch *9 |
|
| 4 |
ECM |
|
| 6 |
Rear fog light relay |
|
| 7 |
Front fog light relay |
|
| 8 |
Turn signal flasher relay |
|
| 9 |
Front passenger seat belt warning light |
|
| 11 |
Daytime running light relay *3, Headlight dimmer switch *4 |
|
| 12 |
Engine oil pressure switch |
|
| 14 |
Battery |
|
| 15 |
Turn signal flasher relay |
|
| 16 |
T-LP relay *4, Daytime running light relay *3 |
|
| D2 *2 |
1 |
Turn signal flasher assembly |
| 2 |
Fog light relay |
|
| 3 |
Rear fog light relay |
|
| 5 |
ECM |
|
| 6 |
Fuel filter switch *9 |
|
| 7 |
Brake fluid level warning switch *10 |
|
| 8 |
Generator (Alternator) |
|
| 9 |
T-LP relay *4 |
|
| 10 |
Turn signal flasher assembly |
|
| 11 |
Battery |
|
| 13 |
Engine oil pressure switch |
|
| 14 |
Headlight dimmer switch |
|
| 16 |
Front passenger seat belt warning light |
|