TERMINALS OF ECU
System information · Vehicles built from Aug 2005
| CHECK AIR CONDITIONING AMPLIFIER |
*2: w/o heater
*3: w/ A/C switch
*4: w/ PTC Heater
If the result is not as specified, there may be a malfunction in the wire harness.


- HINT:
- Check from the rear of the connector while it is connected to the air conditioning amplifier.
| Symbols (Terminals No.) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| S5-3 (E8-1) - GND (E8-12) |
Y - W-B |
Power supply for pressure sensor |
Ignition switch: on (IG) |
4.5 to 5.5 V |
| TX+ (E8-2) - GND (E8-12) |
V - W-B |
CAN communication line |
Ignition switch: on (IG) |
Pulse generation (see waveform 1) |
| TX- (E8-3) - GND (E8-12) |
W - W-B |
CAN communication line |
Ignition switch: on (IG) |
Pulse generation (see waveform 2) |
| SG-2 (E8-4) - Body ground |
L - Body ground |
Ground for evaporator temperature sensor |
Always |
Below 1.0 Ω |
| TAM (E8-5)*1 - SG-1 (E8-11) |
W - B |
Ambient temperature sensor signal |
Ignition switch: on (IG) |
1.35 to 1.75 V |
| Ambient temperature: 25 °C | ||||
| PRE (E8-6) - SG-1 (E8-11) |
GR - B |
Air conditioning pressure sensor signal |
Refrigerant pressure: normal |
0.76 to 4.74 V |
| PRE (E8-6) - SG-1 (E8-11) |
GR - B |
Air conditioning pressure sensor signal |
Refrigerant pressure: Abnormal (less than 0.196 kPa [2.0 kgf/cm2] or more than 3.14 MPa [32 kgf/cm2]) |
Below 0.76 V or 4.74 V or more |
| SOL+ (E8-7) - GND (E8-12) |
LG - W-B |
A/C compressor operation signal |
Engine idling |
Pulse generation (see waveform 3) |
| Heater control (blower switch): 1 | ||||
| A/C switch: ON | ||||
| IG+ (E8-8) - GND (E8-12) |
Y - W-B |
Power source (IG) |
Ignition switch: on (IG) |
10 to 14 V |
| SBLW (E8-9) - GND (E8-12) |
BR - W-B |
Blower motor ON signal |
Ignition switch: on (IG) |
10 to 14 V → Below 1 V |
| Heater control (blower switch): 0 → 1 | ||||
| TE (E8-10) - SG-2 (E8-4) |
GR - L |
Evaporator temperature sensor signal |
Ignition switch: on (IG) |
1.0 to 1.3 V |
| Temperature near evaporator: 15°C (59°F) | ||||
| SG-1 (E8-11) - Body ground |
B - Body ground |
Ground for ambient temperature sensor |
Always |
Below 1.0 Ω |
| GND (E8-12) - Body ground |
W-B - Body ground |
Ground for main power supply |
Always |
Below 1.0 Ω |
| B/V (E8-14)*2 - SG-2 (E8-4) |
LG - Body ground |
Room temperature set signal |
Ignition switch: on (IG) |
4.5 to 5.5 V → Below 1 V |
| No. 3 heater control knob: OFF → Max cool | ||||
| A/C (E8-15)*3 - GND (E8-12) |
LG - W-B |
A/C switch signal |
Ignition switch: on (IG) |
Below 1 V → 10 to 14 V |
| A/C switch: OFF → ON | ||||
| LED (E8-16)*3 - Body ground |
P - Body ground |
A/C switch indicator signal |
Engine idling |
10 to 14 V → Below 4 V |
| A/C switch: ON | ||||
| Heater control (blower switch): 0 → 1 | ||||
| PTC1 (E9-9)*4 - GND (E8-12) |
V - W-B |
PTC heater relay operation signal |
Engine idling |
Below 1 V → 10 to 14 V |
| No. 3 heater control knob: Max hot | ||||
| Engine coolant temperature: Below 65°C (149°F) | ||||
| Ambient temperature: Below 10°C (50°F) | ||||
| Heater control (blower switch): 0 → 1 | ||||
| Waiting time: 10 seconds | ||||
| PTC2 (E9-10)*4 - GND (E8-12) |
BR - W-B |
PTC heater relay operation signal |
Engine idling |
Below 1 V → 10 to 14 V |
| No. 3 heater control knob: Max hot | ||||
| Engine coolant temperature: Below 65 °C (149 °F) | ||||
| Ambient temperature: Below 10 °C (50 °F) | ||||
| Heater control (blower switch): 0 → 1 | ||||
| Waiting time: 20 seconds | ||||
| PTC3 (E9-12)*4 - GND (E8-12) |
R - W-B |
PTC heater relay operation signal |
Engine idling |
Below 1 V → 10 to 14 V |
| No. 3 heater control knob : Max hot | ||||
| Engine coolant temperature: Below 65 °C (149 °F) | ||||
| Ambient temperature: Below 10 °C (50 °F) | ||||
| Heater control (blower switch): 0 → 1 | ||||
| Waiting time: 30 seconds | ||||
| HEAT (E9-14)*4 - Body ground |
LG - Body ground |
MAX HOT switch detection signal |
Ignition switch: on (IG) |
10 to 14 V |
| No. 3 heater control knob: Max hot | ||||
| HLS (E9-23)*4 - Body ground |
LG - Body ground |
Headlight control signal |
Engine idling |
Below 1.0 Ω |
| Light control switch: head position | ||||
| ALT (E9-24)*4 - GND (E8-12) |
P - W-B |
Alternator operation signal |
Engine idling |
Pulse generation |
Waveform 1 (Reference) : Using an oscilloscope

CAN communication signal Terminal Name
Between TX+ (E8-2) - GND (E8-12)
Tester Range
1 V / DIV., 10 μsec. / DIV.
Condition
Ignition switch on (IG)
- HINT:
- The waveform varies depending on the CAN communication signal.
Waveform 2 (Reference) : Using an oscilloscope

CAN communication signal Terminal Name
Between TX- (E8-3) - GND (E8-12)
Tester Range
1 V / DIV., 10 μsec. / DIV.
Condition
Ignition switch on (IG)
- HINT:
- The waveform varies depending on the CAN communication signal.
Waveform 3 (Reference) : Using an oscilloscope

A/C compressor operation signal Terminal Name
Between SOL+ (E8-7) - GND (E8-12)
Tester Range
5 V/ DIV., 500 μsec./ DIV.
Condition
Engine idling, blower switch 1, A/C switch ON