REMOVAL
Removal / installation · Vehicles built from Jan 2006
- NOTICE:
- Always use "Torx" socket wrench E10 when removing the rear seat.
- HINT:
- The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.
| 1. REMOVE CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) |
Remove the 2 package tray trim suspenders.

Remove the 5 pieces of hook tape.
Disengage the 2 claws and remove the package tray trim.
| 3. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board) |
Release the 2 knobs and remove the deck board.

| 4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board) |
Remove the spare wheel cover.

| 5. REMOVE DECK FLOOR BOX (w/ Deck Board) |
for RH Side:
Remove the deck floor box (Click here).
for LH Side:
Remove the deck floor box.
- HINT:
- Use the same procedure as for the RH side.
| 6. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board) |
Remove the rear floor carpet.

| 7. REMOVE REAR SEAT LEG COVER |
for RH Side:
Remove the rear seat leg cover (Click here).
for LH Side:
Remove the rear seat leg cover (Click here).
| 8. REMOVE REAR SEAT ASSEMBLY |
for RH Side:
Remove the rear seat assembly (Click here).
for LH Side:
Remove the rear seat assembly (Click here).
| 9. REMOVE FRONT DOOR SCUFF PLATE |
Disengage the 8 claws and remove the front door scuff plate.

| 10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP |
Remove the front door opening trim weatherstrip to the extent that the front quarter trim panel can be removed.

| 11. REMOVE REAR SEAT SHOULDER BELT HANGER |
Remove the belt of the rear seat outer belt.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the rear seat shoulder belt hanger.

| 12. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY |
Remove the 2 bolts and the front seat outer belt bar.

| 13. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY |
Disengage the 8 clips, the retainer and the 10 claws and remove the front quarter trim panel.

| 14. REMOVE REAR DECK TRIM COVER |
for Grand Tire:

Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
for Temper Spare Tire:

Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
| 15. REMOVE DECK TRIM SIDE PANEL ASSEMBLY |
Remove the bolt.

Disengage the clip and remove the anchor plate of the rear seat outer belt.
for RH Side:

Remove the 3 screws.
Disengage the 3 clips and the 3 claws and remove the deck trim side panel.
for LH Side:

Remove the 3 screws.
Disengage the 3 clips and the 3 claws.
Disconnect the luggage compartment room light connector and remove the deck trim side panel.
| 16. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the center belt guide.

| 17. REMOVE ROOF SIDE INNER GARNISH |
for RH Side:

- NOTICE:
- Replace the special clip with a new one because it is damaged when the roof side inner garnish is removed.
w/ Curtain Shield Airbag:
- Disengage the 4 clips and claw.
- Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
- Disengage the 4 clips and claw.
w/o Curtain Shield Airbag:

- Disengage the 4 clips and claw.
- Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
- Disengage the 4 clips and claw.
for LH Side:

- NOTICE:
- Replace the special clip with a new one because it is damaged when the roof side inner garnish is removed.
(w/ Curtain Shield Airbag)
- Disengage the 4 clips and claw.
- Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
- Disengage the 4 clips and claw.
w/o Curtain Shield Airbag:

- Disengage the 4 clips and claw.
- Pass the rear seat outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.
- Disengage the 4 clips and claw.
| 18. REMOVE REAR SEAT OUTER BELT ASSEMBLY |
Remove the bolt and the through anchor.

Remove the bolt, the 2 hooks and the retractor.

| 19. REMOVE SEAT BELT HOLE SEAL |
Disengage the 2 claws and remove the seat belt hole seal.

