2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL ENGINE SWITCH (for RHD)

A104500
  1. Engage the 2 claws to install the switch.

  1. Connect the switch connector.


2. INSTALL ENGINE SWITCH (for LHD)

A115454
  1. Engage the 2 claws to install the switch.

  1. A115455
    Connect the switch connector.


3. INSTALL INSTRUMENT PANEL BOX (for RHD)

B108189E01
  1. Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.

  1. Engage the 2 hinges with the instrument panel open.

  1. Close the instrument panel box.


4. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY UPPER (for LHD)

B108233E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the upper side of the instrument panel.

  1. Engage the claw and the 3 clips at the lower side of the instrument panel.

    B105355E01

  1. Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt

  1. Connect the connectors.

    B105354E01

  1. B108182
    Connect the passenger airbag connector and clamp.


5. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (for LHD)

B105352
  1. Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.

  1. B108202
    Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.


6. INSTALL SWITCH BASE HOLE COVER (for LHD)

B108201
  1. Disengage the 2 clips and 2 claws and install the switch hole base.


7. INSTALL FRONT PILLAR GARNISH RH (for LHD)

  1. B114342E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127672
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127674
      Connect the speaker connector.

  1. B114312
    Install the 3 antenna cord clamps.

  1. Connect the connector.

  1. w/ Curtain Shield Airbag:

    1. B117697E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B117694
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


8. INSTALL FRONT PILLAR GARNISH LH (for LHD)

  1. B114344E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127671
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127673
      Connect the speaker connector.

  1. B114316
    Install the 4 wire harness clamps.

  1. w/ Curtain Shield Airbag:

    1. B117698E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B114318
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for LHD)
  1. Install the front door opening trim weatherstrip.


10. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD)
  1. Install the front door opening trim weatherstrip.


11. INSTALL INSTRUMENT CLUSTER FINISH PANEL (for LHD)

B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. B132367
    Engage the 4 claws and 5 clips and install the instrument cluster finish panel.


12. INSTALL COMBINATION METER ASSEMBLY (for LHD)

E107730
  1. Install the combination meter assembly with the 2 screws.

  1. Connect the 2 connectors.


13. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (for LHD)

E107743
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.

  1. E107744
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.


14. INSTALL INSTRUMENT PANEL FINISH PANEL END LH (for LHD)

E107741
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.

  1. E107742
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.


15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


16. CHECK SRS WARNING LIGHT (for LHD)
(Click here)
← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →