2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. BOLTS, SCREWS AND NUTS TABLE (for LHD)

HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.


B118994E01

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE INSTRUMENT PANEL FINISH PANEL END LH (for LHD)

E107741E01
  1. with CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.

  1. E107742E01
    Except CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.


4. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for LHD)

E107743E01
  1. with CD player

    1. Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.

  1. E107744E01
    Except CD player

    1. Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.


5. REMOVE INSTRUMENT CLUSTER FINISH PANEL (for LHD)

B132363E01

NOTICE:
Follow the procedure below to remove the instrument cluster finish panel. Claw A will break if the instrument cluster finish panel is raised carelessly.

  1. B132364
    Disengage the 2 claws and 5 clips.

  1. B132365E01
    After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.

  1. Disengage the 3 A claws and remove the instrument cluster finish panel.


6. REMOVE COMBINATION METER ASSEMBLY (for LHD)

E107730
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.


7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for LHD)
  1. Separate the front door opening trim weatherstrip.


8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD)
  1. Separate the front door opening trim weatherstrip.


9. REMOVE FRONT PILLAR GARNISH RH (for LHD)

  1. B117693E01
    w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B117694
    w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B114312
    Disconnect the connector.

  1. Using a clip remover, remove the 3 antenna cord clamps.

  1. B127674
    w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.

    2. B127670E01
      Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.

  1. w/ Curtain Shield Airbag:

    1. B114313E01
      Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)


10. REMOVE FRONT PILLAR GARNISH LH (for LHD)

  1. B117695E01
    w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B117696
    w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B114316
    Using a clip remover, remove the 4 wire harness clamps.

  1. B127673
    w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.

    2. B127669E01
      Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.

  1. B114317E01
    w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)


11. REMOVE SWITCH HOLE BASE (for LHD)

B108201
  1. Disengage the 2 clips and 2 claws and remove the switch hole base.


12. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for LHD)

B108202
  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.

  1. B105351
    Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door assembly.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.


13. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY UPPER (for LHD)

B108181E02
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.

  1. Remove the 2 <C> bolts and 4 <B> screws.

    B105354E01

  1. Disconnect the connectors.

  1. Disengage the claw and 3 clips while lifting the rear instrument panel up.

  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws of the front side of the instrument panel and remove the instrument panel.

    B105355E01


14. REMOVE INSTRUMENT PANEL BOX (for RHD)

B108188E01
  1. Open the instrument panel box.

  1. Pull the hinge side of the instrument panel box out horizontally with the instrument panel open and disengage the 2 hinges.

  1. Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.


15. REMOVE ENGINE SWITCH (for LHD)

A115455
  1. Disconnect the switch connector.

  1. A115454
    Disengage the 2 claws and remove the switch.


16. REMOVE ENGINE SWITCH (for RHD)
  1. Disconnect the switch connector.

  1. A104500
    Disengage the 2 claws and remove the switch.

← COMPONENTS (from Nov 2005)INSPECTION (from Nov 2005) →