INSTALLATION
Removal / installation · Vehicles built from Nov 2006
| 1.
INSTALL STARTER CUT RELAY |
 |
Install the starter cut relay.
| 2.
INSTALL INSTRUMENT PANEL SUB-ASSEMBLY UPPER
|
 |
Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).
Engage the 5 claws at the upper side of the instrument panel.
Engage the claw and the 3 clips at the lower side of the instrument panel.


Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.
-
Torque:
- 20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
for bolt
Connect the connectors.


- Connect the passenger airbag connector and clamp.
| 3.
INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
|
 |
Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.
- NOTICE:
- Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.
- Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.
| 4.
INSTALL SWITCH HOLE BASE
|
 |
Disengage the 2 clips and 2 claws and install the switch hole base.
| 5.
INSTALL FRONT PILLAR GARNISH RH
|
 |
- w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
- w/ Front No. 2 Speaker:
Insert the hook into the body hole.
Engage the clip and install the front speaker.
- Connect the speaker connector.
- Install the 3 antenna cord clamps.
Connect the connector.
w/ Curtain Shield Airbag:
- Install a new special clip and the clip onto a new front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
w/o Curtain Shield Airbag:
- Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 6.
INSTALL FRONT PILLAR GARNISH LH
|
 |
- w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
- w/ Front No. 2 Speaker:
Insert the hook into the body hole.
Engage the clip and install the front speaker.
- Connect the speaker connector.
- Install the 4 wire harness clamps.
w/ Curtain Shield Airbag:
- Install a new special clip and the clip onto a new front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
w/o Curtain Shield Airbag:
- Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 7.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
|
 |
Install the front door opening trim weatherstrip.
| 8.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
|
 |
Install the front door opening trim weatherstrip.
| 9.
INSTALL INSTRUMENT CLUSTER FINISH PANEL
|
 |
Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.
- Engage the 4 claws and 5 clips and install the instrument cluster finish panel.
| 10.
INSTALL COMBINATION METER ASSEMBLY
|
 |
Install the combination meter assembly with the 2 screws.
Connect the 2 connectors.
| 11.
INSTALL INSTRUMENT CLUSTER FINISH PANEL
|
 |
Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.
- Engage the 4 claws and 5 clips and install the instrument cluster finish panel.
| 12.
INSTALL INSTRUMENT PANEL FINISH PANEL END RH
|
 |
with CD player
Connect the connector.
Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.
- Except CD player
Connect the connector.
Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.
| 13.
INSTALL INSTRUMENT PANEL FINISH PANEL END LH
|
 |
with CD player
Connect the connector.
Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.
- Except CD player
Connect the connector.
Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.
| 14.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
 |
-
Torque:
- 5.4 N*m{
55 kgf*cm
, 48 in.*lbf
}
| 15.
INSPECT SRS WARNING LIGHT
|
 |
(Click here)