2005-2008 Yaris · Service Manual DRIVE LINE

REMOVAL

Removal / installation · Vehicles built from Aug 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DRAIN AUTOMATIC TRANSAXLE FLUID (for U441E Automatic Transaxle)
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


3. DRAIN AUTOMATIC TRANSAXLE FLUID (for U340E Automatic Transaxle)
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


4. DRAIN TRANSAXLE OIL (for C551 Manual Transaxle)
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


5. DRAIN TRANSAXLE OIL (for C54 Manual Transaxle)
  1. Remove the filler plug and the gasket.

  1. Remove the drain plug and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


6. REMOVE FRONT WHEEL

7. REMOVE FRONT AXLE HUB NUT

C085629E01
  1. Using SST and a hammer, release the staked part of the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the axle hub nut.
    4. Do not damage the threads of the drive shaft.

  1. Using a 30 mm socket wrench, remove the axle hub nut.


8. SEPARATE FRONT SPEED SENSOR

C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.

  1. C112274
    Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Keep the speed sensor tip and installation portion free of foreign matter.
    2. Remove the speed sensor without turning it from its original installation angle.


9. SEPARATE TIE ROD END SUB-ASSEMBLY
  1. Remove the cotter pin and castle nut.

  1. C116895E01
    Using SST, separate the tie rod end from the steering knuckle.
    SST
    09628-62011  

    NOTICE:
    Do not damage the tie rod end dust cover.


10. SEPARATE FRONT STABILIZER LINK ASSEMBLY

C106044
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


11. SEPARATE FRONT SUSPENSION LOWER ARM

C107513
  1. Remove the clip and castle nut.

  1. C107514E01
    Using SST, separate the lower arm.
    SST
    09628-00011  

    NOTICE:
    1. Do not damage the lower ball joint dust cover.
    2. Suspend SST with a piece of string or the equivalent.


12. SEPARATE FRONT AXLE ASSEMBLY
  1. Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.

    HINT:
    If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.

  1. Push the front axle out of the vehicle to remove the drive shaft from the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Do not damage the speed sensor rotor.
    4. Suspend the drive shaft with a piece of string or the equivalent.


13. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

C107924
  1. Using SST, remove the drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


14. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

C116896
  1. Using a screwdriver and hammer, remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


15. FIX FRONT AXLE ASSEMBLY

C112583E01
SST
09608-16042   (09608-02021, 09608-02041)

HINT:
The hub bearing could be damaged if it is subjected to the vehicle's full weight, such as when moving the vehicle with the drive shaft removed. If it is absolutely necessary to place the vehicle's full weight on the hub bearing, first support it with SST.

← COMPONENTS (from Aug 2005)DISASSEMBLY (from Aug 2005) →