2005-2008 Yaris · Service Manual DRIVE LINE

REASSEMBLY

Removal / installation · Vehicles built from Aug 2005


1. INSTALL FRONT DRIVE SHAFT DUST COVER

F047438E01
  1. Using SST and a press, install a new dust cover into the inboard joint until it is flush with the end.

    SST
    09527-10011  

    NOTICE:
    1. Install the dust cover in the correct orientation.
    2. Do not deform the dust cover.


2. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING
  1. Install a new snap ring.


3. INSTALL FRONT AXLE OUTBOARD JOINT BOOT
  1. Wrap the spline of the outboard joint shaft with protective tape.

  1. Install new parts onto the outboard joint shaft in the following order.

    1.
    Front axle outboard joint boot No. 2 clamp
    2.
    Front axle outboard joint boot
    3.
    Front axle outboard joint boot clamp

  1. Pack the joint portion of the outboard joint shaft and outboard joint boot with grease.

    Standard Quantity:
    Engine Type
    Quantity
    1NZ-FE
    125 to 135 g (4.4 to 4.8 oz.)
    2NZ-FE
    90 to 100 g (3.2 to 3.5 oz.)
    1KR-FE
    77 to 87 g (2.7 to 3.1 oz.)

  1. Install the outboard joint boot onto the outboard joint shaft groove.

    NOTICE:
    Keep the groove free of grease.


4. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

  1. for 1NZ-FE and 2NZ-FE:

    CAUTION:
    Wear protective gloves to avoid injuries to your hands.


    1. C107943
      Install the boot clamp onto the outboard joint boot and provisionally bend the lever.

      NOTICE:
      1. Set the lever into the guide groove correctly.
      2. Check the band and the lever for any deformation before bending the lever.
      3. Set the lever into the guide groove correctly and install the clamp as far into the inner side of the vehicle as possible.

    2. C112269E01
      Lean your weight on your hand and roll the outboard joint forward while pressing the outboard joint against the work plane. Roll the outboard joint and fold the lever until a click sound can be heard.

      NOTICE:
      1. Do not damage the deflector.
      2. Make sure that the outboard joint is in direct contact with the work plane.

    3. C112270
      Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.

      NOTICE:
      Do not damage the outboard joint boot.

  1. for 1KR-FE:

    1. Fix the outboard joint shaft in a vise between aluminum plates.

      NOTICE:
      Do not overtighten the vise.

    2. C112671E01
      Place SST onto the boot clamp, press it against the boot and slightly tighten SST.
      SST
      09521-24010  

    3. Fix SST and tighten it so that the clearance comes to within the specified range.

      Standard Clearance:
      0.8 mm (0.031 in.) or less

    4. Remove SST.

    5. C112672E01
      Using SST, measure the clearance of the boot clamp as shown in the illustration.
      SST
      09240-00020  

      Standard Clearance:
      0.8 mm (0.031 in.) or less

      NOTICE:
      If the clearance is outside the specified range, retighten it.


5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

  1. for 1NZ-FE and 2NZ-FE:

    CAUTION:
    Wear protective gloves to avoid injuries to your hands.


    1. C107948
      Install the boot clamp onto the outboard joint boot and provisionally bend the lever.

      NOTICE:
      1. Set the lever into the guide groove correctly.
      2. Check the band and the lever for any deformation before bending the lever.

    2. C112271E01
      Using water pump pliers, pinch the boot clamp to provisionally fix it.

    3. C112272
      Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.

      NOTICE:
      Do not damage the outboard joint boot.

  1. C112669E01
    for 1KR-FE:

    1. Place SST onto the boot clamp, press it against the boot and slightly tighten SST.

      SST
      09521-24010  

    2. Fix SST and tighten it so that the clearance comes to within the specified range.

      Standard Clearance:
      0.8 mm (0.031 in.) or less

    3. Remove SST.

    4. C112670E01
      Using SST, measure the clearance of the boot clamp as shown in the illustration.
      SST
      09240-00020  

      Standard Clearance:
      0.8 mm (0.031 in.) or less

      NOTICE:
      If the clearance is outside the specified range, retighten it.


6. INSTALL FRONT DRIVE SHAFT DAMPER (for RH Side)

C116898E01
  1. Install the drive shaft damper onto dimension (A) shown in the illustration.

    Dimension (A):
    Engine Type
    Dimension (A)
    1NZ-FE
    425.6 to 429.6 mm
    (16.76 to 16.91 in.)
    2NZ-FE
    416.0 to 420.0 mm
    (16.38 to 16.54 in.)
    1KR-FE
    396.0 to 400 mm
    (15.59 to 15.75 in.)


7. INSTALL FRONT DRIVE SHAFT DAMPER CLAMP (for RH Side)

C116897E01
  1. Using needle-nose pliers, align the concave part with the protrusion of a new damper clamp in order to fix it.


8. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Install new parts onto the outboard joint shaft in the following order.

    1.
    Front axle inboard joint boot clamp
    2.
    Front axle inboard joint boot
    3.
    Front axle inboard joint boot No. 2 clamp

  1. Fix the outboard joint shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Remove the protective tape.

  1. F047445E01
    Align the matchmarks and install the tripod joint onto the outboard joint shaft.

    NOTICE:
    Face the serrated side of the tripod joint outward and install it onto the outboard joint end.

  1. Using a brass bar and hammer, install the tripod joint.

    NOTICE:
    1. Do not hit the roller portion.
    2. Keep the tripod joint free of foreign matter.

  1. C112599
    Using a snap ring expander, install a new snap ring.

  1. Pack the inboard joint with grease.

    Standard Quantity:
    Engine Type
    Quantity
    1NZ-FE
    125 to 135 g (4.4 to 4.8 oz.)
    2NZ-FE
    112 to 122 g (4.0 to 4.3 oz.)
    1KR-FE
    108 to 118 g (3.8 to 4.2 oz.)

  1. F047434E01
    Align the matchmarks and install the inboard joint onto the outboard joint shaft.


9. INSTALL FRONT AXLE INBOARD JOINT BOOT
  1. Install the inboard joint boot into the grooves of the inboard joint and outboard joint shaft.

    NOTICE:
    Keep the grooves free of grease.


10. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

C081794
  1. for One-touch Clamp Type:

    1. Install the boot clamp onto the inboard joint boot and caulk the boot clamp with a screwdriver.

      NOTICE:
      Do not damage the boot.

  1. F047432E01
    for Hook Clamp Type:

    1. Using needle-nose pliers, align the concave part with the protrusion of the boot clamp in order to fix it.

      NOTICE:
      1. Do not damage the boot.
      2. Do not deform the claw of the hook.


11. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

C081795
  1. for One-touch Clamp Type:

    1. Install the boot clamp onto the inboard joint boot and caulk the boot clamp with a screwdriver.

      NOTICE:
      Do not damage the boot.

  1. F047433E01
    for Hook Clamp Type:

    1. Using needle-nose pliers, align the concave part with the protrusion of the boot clamp in order to fix it.

      NOTICE:
      1. Do not damage the boot.
      2. Do not deform the claw of the hook.


12. INSPECT FRONT DRIVE SHAFT

C107965E01
  1. Check whether the drive shaft dimensions are within the following specifications.

    HINT:
    The following table shows dimension (A) of the drive shaft.

    Dimension (A):
    Engine Type
    LH
    RH
    1NZ-FE
    584.3 mm
    (23.00 in.)
    826.3 mm
    (32.53 in.)
    2NZ-FE
    589.3 mm
    (23.20 in.)
    829.3 mm
    (32.65 in.)
    1KR-FE
    597.7 mm
    (23.53 in.)
    814.7 mm
    (32.07 in.)

  1. C110169
    Check for noticeable looseness when turning the joint up and down, left and right, and in the thrust direction.

  1. Check for cracks, damage and grease leakage on the boot joint.

    NOTICE:
    Keep the drive shaft level while moving it.

← DISASSEMBLY (from Aug 2005)INSTALLATION (from Aug 2005) →