2005-2008 Yaris · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Jan 2006

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

NOTICE:
Always use "Torx" socket wrench E10 when removing the rear seat.

HINT:
The procedure described below is for the RH side. Use the same procedure for both the LH and RH sides, unless otherwise specified.


1. INSTALL REAR AIRBAG SENSOR
  1. Confirm that the ignition switch is turned to off.

  1. Confirm that the negative battery terminal is detached.

    CAUTION:
    1. Confirm that the negative battery terminal is disconnected before performing the operation. Even an impact to only the airbag sensor will cause the airbag to deploy.

  1. B106578E01
    Insert the hook into the body hole and install the airbag sensor with the bolt.

    Torque:
    9.0 N*m{ 90 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. Do not use a rear airbag sensor that has been dropped.
    2. Do not subject the rear airbag sensor to any impact or force.

  1. Confirm that there is no looseness by shaking the rear airbag sensor.

  1. B106579E01
    Connect the airbag connector.


2. INSTALL DECK SIDE TRIM PANEL ASSEMBLY RH

  1. C123148E01
    Engage the 3 clips and the 3 claws and install the deck side trim panel.

  1. Tighten the 3 screws.

    HINT:
    When installing the deck trim side panel assembly LH onto the vehicle with the luggage compartment room light, connect the room light connector and then install the deck trim side panel assembly.


3. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH

  1. B114500
    Engage the clip and install the anchor plate.

  1. Tighten the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


4. INSTALL REAR DECK TRIM COVER

  1. B114283
    for Grand Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.

  1. B117692
    for Temper Spare Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.


5. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

  1. B114499
    Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.

  1. B114498
    Install the belt of the rear seat outer belt onto the rear seat shoulder belt hanger.


6. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH

  1. B114759
    Install the front seat outer belt bar with the 2 bolts.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


7. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B114546E01
    Align the locating mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint mark: 
    Area
    Color
    RH side
    Blue
    LH side
    Pink


8. INSTALL FRONT DOOR SCUFF PLATE RH

  1. B114494
    Engage the 8 claws and install the front door scuff plate.


9. INSTALL REAR SEAT ASSEMBLY LH

  1. B124363E01
    Insert the 2 locating pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B124331E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


10. INSTALL REAR SEAT ASSEMBLY RH

  1. B124326E01
    Insert the 2 locating pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B124299E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


11. INSTALL NO. 2 REAR SEAT LEG COVER

  1. B124330
    Engage the 6 claws and install the No. 2 rear seat leg cover.


12. INSTALL NO. 1 REAR SEAT LEG COVER

  1. B124298
    Engage the 4 claws and install the rear seat No. 1 leg cover.


13. INSTALL DECK FLOOR BOX RH (w/ Deck Board)

  1. B106446
    Set the deck floor box and lock the 2 knobs.


14. INSTALL DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.


15. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B138393
    Install the spare wheel cover.


16. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106447
    Set the deck board and lock the 2 knobs.


17. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B106447
    Set the deck board and lock the 2 knobs.


18. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.


19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


20. INSPECT SRS WARNING LIGHT
(Click here)
← REMOVAL (from Jan 2006)COMPONENTS (from Nov 2005) →