2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Aug 2005 – Dec 2005

Versions by build date: Aug 2005 – Dec 2005 from Jan 2006


1. INSTALL EXHAUST PIPE ASSEMBLY TAIL

  1. Install the 2 exhaust pipe support No. 4 and the exhaust tail pipe assembly.

    A115390


2. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for Leaded Gasoline Specification Vehicle)

A104634
  1. Using vernier calipers, measure the free length of the compression spring.

    Minimum length (Front Side):
    40.5 mm (1.594 in.)
    Minimum length (Rear Side):
    38.5 mm (1.516 in.)

    If the length is not as specified, replace the compression spring.

  1. A104635E01
    Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Install the exhaust pipe gasket in the correct direction.
    2. Do not damage the outer surface of the exhaust pipe gasket.
    3. Do not reuse the exhaust pipe gasket.
    4. Do not push in the gasket with the exhaust pipe when connecting it.

  1. Install the 3 exhaust pipe support No. 4.

  1. Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }


    A115389


3. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for Unleaded Gasoline Specification Vehicle)

A104634
  1. Using vernier calipers, measure the free length of the compression spring.

    Minimum length:
    40.5 mm (1.594 in.)
    Minimum length:
    38.5 mm (1.516 in.)

    If the length is not as specified, replace the compression spring.

  1. A104635E01
    Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Install the exhaust pipe gasket in the correct direction.
    2. Do not damage the outer surface of the exhaust pipe gasket.
    3. Do not reuse the exhaust pipe gasket.
    4. Do not push in the gasket with the exhaust pipe when connecting it.

  1. Install the 3 exhaust pipe support No. 4.

  1. Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }


    A119126


4. INSTALL HEATED OXYGEN SENSOR (for Unleaded Gasoline Specification Vehicle)

A115424
  1. Using SST, install the sensor onto the front exhaust pipe.

    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }

  1. Pass the sensor connector through the floor panel and install the grommet.

  1. Connect the sensor connector.


5. INSTALL CONSOLE BOX ASSEMBLY REAR

C116873
  1. Engage the 2 clips and install the console box with the bolt.


6. INSTALL CONSOLE BOX REAR COVER

C109006E01
  1. Engage the 8 claws to install the console box rear cover.


7. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)

C109005E01
  1. Engage the 6 claws to install the shifting hole cover.


8. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


10. CHECK FOR EXHAUST GAS LEAKAGE
← REMOVAL (from Jan 2006)INSTALLATION (from Jan 2006) →