2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL BRAKE MASTER CYLINDER
  1. Install a new O-ring onto the brake master cylinder.

  1. C128992
    Install the brake master cylinder with the 2 new nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. C128991E01
    w/o VSC:

    1. Using SST, install the 2 brake tubes onto the brake master cylinder.

      SST
      09023-00100  

      Torque:
      for use without SST:
      15 N*m{ 155 kgf*cm , 11 ft.*lbf }
      for use with SST:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      2. This torque value is effective when SST is parallel to a torque wrench.

  1. w/ VSC:

    1. Using SST, install the 2 brake tubes onto the brake master cylinder.

      SST
      09023-38200  

      Torque:
      for use without SST:
      20 N*m{ 199 kgf*cm , 14 ft.*lbf }
      for use with SST:
      18 N*m{ 180 kgf*cm , 13 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      2. This torque value is effective when SST is parallel to a torque wrench.

  1. Connect the brake fluid level warning switch connector.


2. CONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)

C128990
  1. Connect the reservoir tube with the clip.


3. INSTALL COWL TOP PANEL OUTER (for 1ND-TV)

A107444
  1. Install the cowl top panel with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }

  1. A117320
    Connect the wire harness clamp.


4. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY (for 1ND-TV)

A108951
  1. Engage the claw to install cowl to register duct No. 2.


5. INSTALL FRONT WIPER MOTOR AND LINK (for 1ND-TV)

E107891
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


6. INSTALL COWL TOP VENTILATOR LOUVER LH (for 1ND-TV)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


7. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for 1ND-TV)

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


8. INSTALL HOOD TO COWL TOP SEAL (for 1ND-TV)

A125202
  1. Engage the 7 clips and install the hood to cowl top seal.


9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for 1ND-TV)

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. A117366E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


10. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for 1ND-TV)

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. A117367E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


11. INSTALL FRONT WIPER ARM HEAD CAP (for 1ND-TV)

  1. E107898
    Engage the claw and install the 2 front wiper arm head caps.


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


13. FILL RESERVOIR WITH BRAKE FLUID

C137247E01
  1. Remove the cowl top ventilator louver.

  1. C130290E01
    Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT4


14. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. C130291E01
    w/o VSC:

    1. Using SST, disconnect the brake tubes from the master cylinder.

      SST
      09023-00100  

  1. w/ VSC:

    1. Using SST, disconnect the brake tubes from the master cylinder.

      SST
      09023-38200  

  1. C130292E01
    Slowly depress the brake pedal and hold it there (Step A).

  1. C130293E01
    Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.

  1. C130291E01
    w/o VSC:

    1. Using SST, connect the brake tubes to the master cylinder.

      SST
      09023-00100  

      Torque:
      for use without SST:
      15 N*m{ 155 kgf*cm , 11 ft.*lbf }
      for use with SST:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      2. This torque value is effective when SST is parallel to a torque wrench.

  1. w/ VSC:

    1. Using SST, connect the brake tubes to the master cylinder.

      SST
      09023-38200  

      Torque:
      for use without SST:
      20 N*m{ 199 kgf*cm , 14 ft.*lbf }
      for use with SST:
      18 N*m{ 180 kgf*cm , 13 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      2. This torque value is effective when SST is parallel to a torque wrench.


15. BLEED BRAKE LINE

C130294
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    Front Disc Brake:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }
    Rear Drum Brake:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
    Rear Disc Brake:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


16. BLEED BRAKE ACTUATOR (w/ VSC)

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with an intelligent tester by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. A107926E08
    Connect the intelligent tester to the DLC3, and turn the ignition switch on (IG).

    NOTICE:
    Do not start the engine.

  1. Select AIR BLEEDING on the intelligent tester.

    HINT:
    Refer to the intelligent tester operator's manual for further details.

  1. Bleed the air out of the brake line when Step 1: Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. C130294
      Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

    3. When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).

    4. Repeat steps E and F until all air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    6. Repeat the above procedure for each wheel to bleed the air out of the brake line.

  1. Bleed the air out of the suction line when Step 2: Inhalation appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator to bleed the air using the intelligent tester (Step G).

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    3. Check if the operation has stopped by referring to the intelligent tester display (Step H).

    4. Repeat steps G and H until all air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (Step I).

    3. Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there.

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.

      HINT:
      1. The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
      2. When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.

    4. Tighten the bleeder plug, then release the brake pedal (Step J).

    5. Repeat steps I and J until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the brake line again when Step 4: Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. C130294
      Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step K).

    3. When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step L).

    4. Repeat steps K and L until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

    7. Make sure that the air bleeding is complete by referring to the intelligent tester display.


17. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT4


18. CHECK FOR BRAKE FLUID LEAKAGE
← REASSEMBLY (from Nov 2005)COMPONENTS (from Jan 2006) →