2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Jan 2006


1. INSTALL BRAKE MASTER CYLINDER
  1. Install a new O-ring onto the brake master cylinder.

  1. C107587
    Install the brake master cylinder with the 2 nuts.

    Torque:
    18 N*m{ 180 kgf*cm , 13 ft.*lbf }

  1. C107586E01
    Using SST, install the 2 brake tubes onto the brake master cylinder.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.

  1. Connect the brake fluid level warning switch connector.


2. CONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)

C107585
  1. Connect the reservoir tube with the clip.


3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


4. FILL RESERVOIR WITH BRAKE FLUID

C133125E01
  1. Remove the cowl top No. 2 ventilator louver center.

  1. C133126E01
    Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4


5. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. C116910E01
    Using SST, disconnect the brake tubes from the master cylinder.
    SST
    09023-00100  

  1. C116911E01
    Slowly depress the brake pedal and hold it there (Step A).

  1. C116912E01
    Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.

  1. C116910E01
    Using SST, connect the brake tubes to the master cylinder.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.


6. BLEED BRAKE LINE

C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


7. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4


8. CHECK FOR BRAKE FLUID LEAKAGE
← REASSEMBLY (from Jan 2006)COMPONENTS (from Nov 2006) →