2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Nov 2006


1. INSTALL BRAKE MASTER CYLINDER

C159554
  1. Temporarily install the brake tube into the union and brake tube way.

  1. Install a new O-ring onto the brake master cylinder.

  1. Install the brake master cylinder onto the brake booster.

  1. C159552
    Temporarily install the union with brake tube and brake tube way into the brake master cylinder with 2 new gaskets and union bolt.

  1. Install the vacuum check valve bracket.

  1. Install the 2 nuts.

    Torque:
    18 N*m{ 180 kgf*cm , 13 ft.*lbf }

  1. C159551
    Fully tighten the union bolt.

    Torque:
    30 N*m{ 310 kgf*cm , 22 ft.*lbf }

  1. C159555E01
    Using SST, fully tighten the 2 brake tubes.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.

  1. C159556E01
    Using SST, install the 2 brake tubes into the brake master cylinder.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.

  1. C159548
    Connect the 4 wire harness clamps.

  1. Connect the brake fluid level warning switch connector.


2. CONNECT CLUTCH RESERVOIR TUBE

C159547
  1. Connect the reservoir tube with the clip.


3. INSTALL OUTER COWL TOP PANEL

A115392
  1. Install the cowl top panel with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. A108438
    Connect the wire harness clamp.


4. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A108437
  1. Engage the claw to install No. 2 cowl to register duct.


5. INSTALL FRONT WIPER MOTOR AND LINK

E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


6. INSTALL COWL TOP VENTILATOR LOUVER LH

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


7. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


8. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


10. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


11. INSTALL FRONT WIPER ARM HEAD CAP

E113849
  1. Engage the claw and install the 2 front wiper arm head caps.


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


13. FILL RESERVOIR WITH BRAKE FLUID

C159579
  1. Disengage the 2 clips and separate the hood to cowl top seal.

  1. Remove the cowl top ventilator louver.

  1. C159562
    Set the brake fluid can upside down onto the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3


14. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. C159549E01
    Using SST, disconnect the brake tubes from the master cylinder.
    SST
    09023-00100  

  1. C159563
    Slowly depress the brake pedal and hold it there (Step A).

  1. C159573
    Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.

  1. C159556E01
    Using SST, connect the brake tubes to the master cylinder.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.


15. BLEED BRAKE LINE

C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    Front Brake:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
    Rear Brake:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


16. BLEED BRAKE ACTUATOR

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with an intelligent tester by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. Connect the intelligent tester to the DLC3, and turn the ignition switch on (IG).

    NOTICE:
    Do not start the engine.

  1. Select AIR BLEEDING on the intelligent tester.

    HINT:
    Refer to the intelligent tester operator's manual for further details.

  1. Bleed the air out of the brake line when Step 1: Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. C116913
      Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

    3. When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).

    4. Repeat steps E and F until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      Front Brake:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      Rear Brake:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    6. Repeat the above procedure for each wheel to bleed the air out of the brake line.

  1. Bleed the air out of the suction line when Step 2: Inhalation appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator to bleed the air using the intelligent tester (Step G).

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    3. Check if the operation has stopped by referring to the intelligent tester display (Step H).

    4. Repeat step G and H until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      Front Brake:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      Rear Brake:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (Step I).

    3. Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there (Step J).

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.

      HINT:
      1. The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
      2. When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.

    4. Tighten the bleeder plug, then release the brake pedal (Step K).

    5. Repeat steps I to K until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      Front Brake:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      Rear Brake:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the brake line again when Step 4: Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. C116913
      Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step L).

    3. When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step M).

    4. Repeat steps L and M until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      Front Brake:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      Rear Brake:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

    7. Make sure that the air bleeding is complete by referring to the intelligent tester display.


17. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3


18. INSPECT FOR BRAKE FLUID LEAK
← REASSEMBLY (from Nov 2006)COMPONENTS (from Aug 2005) →