2005-2008 Yaris · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.


3. REMOVE FRONT WIPER ARM HEAD CAP

E107882E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E107883
    Remove the nut and front wiper arm.


6. REMOVE HOOD TO COWL TOP SEAL

A125202
  1. Disengage the 7 clips and remove the hood to cowl top seal.


7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


8. REMOVE COWL TOP VENTILATOR LOUVER LH

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


9. REMOVE FRONT WIPER MOTOR AND LINK

E107890
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


10. REMOVE NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A108951
  1. Disengage the claw and remove cowl to register duct sub-assembly No. 2.


11. REMOVE COWL TOP PANEL OUTER

A117320
  1. Disengage the wire harness clamp.

  1. A107444
    Remove the 9 bolts and remove the cowl top panel outer.


12. REMOVE INSTRUMENT PANEL NO. 1 UNDER COVER SUB-ASSEMBLY

  1. B114571
    Disengage the 4 claws and remove the instrument panel under cover.


13. REMOVE INSTRUMENT PANEL UNDER TRAY (w/o Driver Side Knee Airbag)

B108185
  1. Disengage the 4 claws and open the instrument panel under tray.

  1. B108187
    Remove the 2 <A> screws.

  1. Disengage the 4 claws and remove the instrument panel under tray.


14. REMOVE STEERING COLUMN COVER (w/ Driver Side Knee Airbag)

C118007
  1. Turn the steering wheel 90 degrees in both directions and remove the 2 screws.

  1. Remove the screw from the lower portion of the steering cover lower.

  1. Disengage the 2 claws and remove the steering column cover lower.


15. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

C119072E01
  1. Remove the 4 screws.

  1. Disengage the 6 claws and remove the driver side knee airbag assembly.

  1. Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, disconnect the airbag connector and remove the instrument panel wire.


16. DISCONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)

C128990
  1. Slide the clip and disconnect the reservoir tube.


17. REMOVE BRAKE MASTER CYLINDER

NOTICE:
Remove the brake master cylinder after depressing the brake pedal several times and bleeding the vacuum pressure from inside the brake booster.

  1. Disconnect the brake fluid level warning switch connector.

  1. C128991E01
    w/o VSC:

    1. Using SST, separate the 2 brake tubes from the brake master cylinder.

      SST
      09023-00100  

  1. w/ VSC:

    1. Using SST, separate the 2 brake tubes from the brake master cylinder.

      SST
      09023-38200  

  1. C128992
    Remove the 2 nuts and remove the brake master cylinder.

  1. Remove the O-ring from the brake master cylinder.


18. REMOVE STOP LIGHT SWITCH

C107592
  1. Disconnect the connector from the stop light switch.

  1. Turn the stop light switch counterclockwise, and remove the stop light switch.


19. REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER

C107593
  1. Remove the stop light switch mounting adjuster from the pedal support.


20. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS

C107594
  1. Remove the brake pedal return spring.

  1. Loosen the push rod lock nut.

  1. Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.

  1. Remove the push rod clevis from the brake booster.


21. REMOVE BRAKE BOOSTER

C107595
  1. Slide the clip and disconnect the vacuum hose from the check valve.

  1. C107596
    Remove the bolt and separate the wire harness bracket.

  1. C107597
    Remove the wire harness clamp and 4 nuts and remove the brake booster.

  1. Remove the gasket from the brake booster.


22. REMOVE VACUUM RESERVOIR VACUUM CHECK VALVE ASSEMBLY

C126205
  1. Remove the vacuum check valve from the brake booster.

  1. Remove the grommet from the brake booster.

← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →