2005-2008 Yaris · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built from Aug 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.


3. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


6. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


8. REMOVE COWL TOP VENTILATOR LOUVER LH

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


9. REMOVE FRONT WIPER MOTOR AND LINK

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


10. REMOVE NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A118801E01
  1. Disengage the claws, and remove the cowl to resister duct No. 2.


11. REMOVE COWL TOP PANEL OUTER

A116498
  1. Disengage the clamp, and separate the wiper motor connector.

  1. A116497
    Remove the 9 bolts and the cowl top panel outer.


12. REMOVE INSTRUMENT PANEL NO. 1 UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel No. 1 Under Cover Sub-assembly)

  1. B114572
    Remove the 2 screws.

  1. Disengage the 3 claws and remove the instrument panel under cover.


13. REMOVE INSTRUMENT PANEL UNDER TRAY (w/o Driver Side Knee Airbag)

B108185
  1. Disengage the 4 claws and open the instrument panel under tray.

  1. B108187
    Remove the 2 <A> screws.

  1. Disengage the 4 claws and remove the instrument panel under tray.


14. REMOVE STEERING COLUMN COVER SUPPORT (w/ Driver Side Knee Airbag)

B108275E01
  1. Disengage the 4 claws and remove the steering column cover support.


15. REMOVE STEERING COLUMN COVER (w/ Driver Side Knee Airbag)

C118007
  1. Turn the steering wheel 90 degrees in both directions and remove the 2 screws.

  1. Remove the screw from the lower portion of the steering cover lower.

  1. Disengage the 2 claws and remove the steering column cover lower.


16. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

C119072E01
  1. Remove the 4 screws.

  1. Disengage the 6 claws and remove the driver side knee airbag assembly.

  1. Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, disconnect the airbag connector and remove the instrument panel wire.


17. REMOVE BATTERY

18. REMOVE BATTERY TRAY

19. REMOVE BATTERY CARRIER

20. REMOVE BRAKE ACTUATOR (w/ ABS)

C121850
  1. Remove the clip and disconnect the wire harness.

  1. Move the lock lever in the direction indicated by the arrow to release the lock and disconnect the brake actuator connector from the actuator.

  1. C116914E01
    Using SST, separate the brake tube from the front flexible hose.
    SST
    09023-00100  

  1. C116915E01
    Using SST, separate the 2 brake tubes from the brake tube No. 1 way.
    SST
    09023-00100  

  1. C121690E01
    Using SST, separate the 2 brake tubes from the brake master cylinder.
    SST
    09023-00100  

  1. C116916
    Using SST, separate the 6 brake tubes from the brake actuator.
    SST
    09023-00100  

  1. C116917E01
    Use tags or labels to identify the place to reconnect each brake tube.

  1. C116918
    Disconnect the brake tube clamp.

  1. C116921
    Remove the 3 bolts and the actuator with bracket.


21. REMOVE ABS AND TRACTION ACTUATOR (w/ VSC)

C116923
  1. Remove the clip and disconnect the wire harness.

  1. Slide the lock lever downward to release the lock and disconnect the connector from the actuator.

  1. C116914E01
    Using SST, separate the brake tube from the front flexible hose.
    SST
    09023-00100  

  1. C116915E01
    Using SST, separate the 2 brake tubes from the brake tube No. 1 way.
    SST
    09023-00100  

  1. C121690E01
    Using SST, separate the 2 brake tubes from the brake master cylinder.
    SST
    09023-00100  

  1. C116924
    Using SST, separate the 6 brake tubes from the brake actuator.
    SST
    09023-00100  

  1. C116925E01
    Use tags or labels to identify the place to reconnect each brake tube.

  1. C116918
    Disconnect the brake tube clamp.

  1. C116926
    Remove the 3 bolts and the actuator with bracket.


22. DISCONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)

C116933
  1. Slide the clip and disconnect the reservoir tube.


23. REMOVE BRAKE MASTER CYLINDER

NOTICE:
Remove the brake master cylinder after depressing the brake pedal several times and bleeding the vacuum pressure from inside the brake booster.

  1. Disconnect the brake fluid level warning switch connector.

  1. C121832E01
    w/o ABS:

    1. Using SST, separate the 3 brake tubes from the brake tube way.

      SST
      09023-00100  

  1. C121690E01
    Using SST, separate the 2 brake tubes from the brake master cylinder.
    SST
    09023-00100  

  1. C116934
    w/ ABS:

    1. Remove the 2 nuts and remove the brake master cylinder.

  1. C121833
    w/o ABS:

    1. Remove the 2 nuts and brake tube way and remove the brake master cylinder.

  1. Remove the O-ring from the brake master cylinder.


24. SEPARATE BRAKE MASTER CYLINDER PUSH ROD CLEVIS

C116880
  1. Remove the brake pedal return spring.

  1. Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.


25. REMOVE BRAKE BOOSTER

C116915E01

  1. w/o ABS:

    1. Using SST, separate the 2 brake tubes from the brake tube No. 1 way.

      SST
      09023-00100  

    2. C121837
      Using SST, remove the brake tube assembly from the proportioning valve.
      SST
      09023-00100  

  1. C116936
    Slide the clip and disconnect the vacuum hose from the check valve.

  1. C116943
    Remove the 4 nuts and remove the brake booster.

  1. Remove the gasket from the brake booster.

  1. Loosen the push rod lock nut and remove the push rod clevis.


26. REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY

C116937
  1. Remove the vacuum check valve from the brake booster.

  1. Remove the grommet from the brake booster.

← COMPONENTS (from Aug 2005)INSTALLATION (from Aug 2005) →