2005-2008 Yaris · Service Manual RESTRAINTS

Trouble in Passenger Airbag OFF Indicator

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

When the airbag cut-off switch is turned off, the passenger airbag OFF indicator illuminates. When the passenger airbag OFF indicator illuminates, both the front passenger airbag assembly and the front passenger side front seat side airbag assembly stop functioning.

WIRING DIAGRAM

H102135E01
H102136E02

INSPECTION PROCEDURE


1. CHECK SRS WARNING LIGHT
  1. Turn the ignition switch on (IG), and check the SRS warning light condition.

    OK:
    The SRS warning light does not come on.



NG
CHECK DTC
OK


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the airbag cut-off switch.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3. INSPECT AIRBAG CUT-OFF SWITCH

  1. H100191E01
    Disconnect the D57 passenger airbag manual cut off switch connector.

  1. Measure the resistance.

    Standard resistance:
    Switch Condition
    Tester Connection
    Specified Condition
    OFF
    1 (PMC-) - 2 (PMC+)
    80 to 120 Ω
    ON
    1 (PMC-) - 2 (PMC+)
    320 to 480 Ω



NG
REPLACE AIRBAG CUT-OFF SWITCH
OK


4. CHECK INSTRUMENT PANEL WIRE (FOR OPEN)

  1. H100193E01
    Disconnect the instrument panel wire connector from the airbag cut-off switch.

  1. Using a service wire, connect D57-1 (PMC-) and D57-2 (PMC+) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-11 (MSW+) - D16-12 (MSW-)
    Always
    Below 1Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


5. CHECK INSTRUMENT PANEL WIRE (FOR SHORT)

  1. H100192E01
    Disconnect the service wire from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-11 (MSW+) - D16-12 (MSW-)
    Always
    1 MΩor Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


6. CHECK INSTRUMENT PANEL WIRE (TO B+)

  1. H100192E01
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D16-11 (MSW+)- Body ground
    Ignition switch on (IG)
    Below 1 V
    D16-12 (MSW-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


7. CHECK INSTRUMENT PANEL WIRE (TO GROUND)

  1. H100192E01
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-11 (MSW+) - Body ground
    Always
    1 MΩor Higher
    D16-12 (MSW-) - Body ground
    Always
    1 MΩor Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY


← SRS Warning Light does not Come ON (from Aug 2005)TC and CG Terminal Circuit (Aug 2005 – Oct 2005) →