2005-2008 Yaris · Service Manual BODY

B2312 Driver Side Door Master Switch Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The driver door power window regulator motor is driven by operating the power window regulator master switch. The driver door power window regulator motor has motor, regulator, and ECU functions.
When the ECU determines that the power window regulator master switch is stuck, DTC B2312 is set.

NOTICE:
  1. The power window control system uses a multiplex communication system (LIN). Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
  2. When the power window regulator motor assembly (on the driver side) is reinstalled or replaced, the power window control system must be initialized.
  3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:
    1. Close the power window by fully pulling up the power window switch and holding it in the AUTO UP position.
    2. Open the power window by fully pushing down the switch.

DTC No.
DTC Detection Condition
Suspected Trouble Area
B2312
Power window regulator master switch assembly stuck
  1. Power window regulator motor assembly (on driver side)
  2. Power window regulator master switch assembly
  3. Wire harness
  4. Power window regulator master switch held in same position for more than 20 seconds

WIRING DIAGRAM

B111516E01

INSPECTION PROCEDURE


1. READ VALUE OF INTELLIGENT TESTER (MASTER SWITCH)
  1. Using the data list to check the function of the power window master switch.

    Power window regulator master switch assembly:
    Item
    Measurement Item/ Display (Range)
    Normal Condition
    Diagnostic Note
    Door P/W Auto SW
    Driver side power window
    AUTO switch signal/ ON or OFF
    ON: Driver side power window AUTO switch operates
    OFF: Driver side power window AUTO switch does not operate
    -
    Door P/W Up SW
    Driver side power window
    UP switch signal/ ON or OFF
    ON: Driver side power window UP switch operates
    OFF: Driver side power window UP switch does not operate
    -
    Door P/W Down SW
    Driver side power window
    DOWN switch signal/ ON or OFF
    ON: Driver side power window DOWN switch operates
    OFF: Driver side power window DOWN switch does not operate
    -

    OK:
    ON (switch operates) appears on screen.

    HINT:
    When the power window operates normally, the problem has been caused by irregular switch operation (the power window regulator master switch was held in the same position for more than 20 seconds.)



OK
END
NG


2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

  1. B119968E01
    Remove the power window regulator master switch assembly.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    18 (U) - 7 (E) - 1 (AUTO)
    AUTO UP
    Below 1 Ω
    10 (D) - 15 (B)
    AUTO UP
    Below 1 Ω
    18 (U) - 7 (E)
    UP
    Below 1 Ω
    10 (D) - 15 (B)
    UP
    Below 1 Ω
    18 (U) - 10 (D) - 15 (B)
    OFF
    Below 1 Ω
    10 (D) - 7 (E)
    DOWN
    Below 1 Ω
    18 (U) - 15 (B)
    DOWN
    Below 1 Ω
    1 (AUTO) - 10 (D) - 7 (E)
    AUTO DOWN
    Below 1 Ω
    18 (U) - 15 (B)
    AUTO DOWN
    Below 1 Ω
    RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    9 (U) - 7 (E) - 18 (AUTO)
    AUTO UP
    Below 1 Ω
    6 (D) - 15 (B)
    AUTO UP
    Below 1 Ω
    9 (U) - 7 (E)
    UP
    Below 1 Ω
    6 (D) - 15 (B)
    UP
    Below 1 Ω
    9 (U) - 6 (D) - 15 (B)
    OFF
    Below 1 Ω
    6 (D) - 7 (E)
    DOWN
    Below 1 Ω
    9 (U) - 15 (B)
    DOWN
    Below 1 Ω
    18 (AUTO) - 6 (D) - 7 (E)
    AUTO DOWN
    Below 1 Ω
    9 (U) - 15 (B)
    AUTO DOWN
    Below 1 Ω

  1. Reinstall the power window regulator master switch assembly.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (MASTER SWITCH ASSEMBLY - MOTOR ASSEMBLY (DRIVER SIDE))

  1. Disconnect the G1 or F7 power window regulator master switch connector.B119970E01

  1. Disconnect the G8 or F8 power window regulator motor connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    G1-18 (U) - G8-10 (U)
    Below 1 Ω
    G1-10 (D) - G8-7 (D)
    Below 1 Ω
    G1-1 (AUTO) - G8-4 (AUTO)
    Below 1 Ω
    G1-6 (LED+) - G8-5 (LED)
    Below 1 Ω
    RHD 
    Tester Connection
    Specified Condition
    F7-9 (U) - F8-10 (U)
    Below 1 Ω
    F7-6 (D) - F8-7 (D)
    Below 1 Ω
    F7-18 (AUTO) - F8-4 (AUTO)
    Below 1 Ω
    F7-16 (LED+) - F8-5 (LED)
    Below 1 Ω

  1. Reconnect the switch and motor connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)


← B2311 Driver Door Motor Malfunction (from Aug 2005)B2313 Glass Position Initialization Incomplete (from Aug 2005) →