2005-2008 Yaris · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from Aug 2005


CHECK MAIN BODY ECU
E114510E06
B108612E02
  1. Disconnect the 4B and 4E main body ECU (vehicle rear side) connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    BECU (4B-30) - GND1 (4E-17)
    L - W-B
    Battery (power supply)
    Always
    10 to 14 V
    GND1 (4E-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the main body ECU (vehicle rear side) connectors.

  4. Measure the voltage of the wire harness side connectors.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DCTY (4A-21) - Body ground
    L - Body ground
    Driver side door courtesy switch input
    Driver side door closed
    10 to 14 V
    DCTY (4A-21) - Body ground
    L - Body ground
    Driver side door courtesy switch input
    Driver side door open
    0 V
    PCTY (4A-24) - Body ground
    R - Body ground
    Passenger side door courtesy switch input
    Passenger side door closed
    10 to 14 V
    PCTY (4A-24) - Body ground
    R - Body ground
    Passenger side door courtesy switch input
    Passenger side door open
    0 V
    RRCY (4A-20) - Body ground
    L - Body ground
    Rear RH door courtesy switch input
    Rear RH door closed
    10 to 14 V
    RRCY (4A-20) - Body ground
    L - Body ground
    Rear RH door courtesy switch input
    Rear RH door open
    0 V
    RRCY (4A-5) - Body ground
    G - Body ground
    Rear LH door courtesy switch input
    Rear LH door closed
    10 to 14 V
    RRCY (4A-5) - Body ground
    G - Body ground
    Rear LH door courtesy switch input
    Rear LH door open
    0 V
    BCTY (4A-7) - Body ground
    SB- Body ground
    Back door courtesy switch input
    Back side door closed
    10 to 14 V
    BCTY (4A-7) - Body ground
    SB- Body ground
    Back door courtesy switch input
    Back side door open
    0 V
    HAZ (4S-17) - Body ground
    B - Body ground
    Hazard warning light signal
    Answer-back ON
    Pulse generation
    HAZ (4S-17) - Body ground
    B - Body ground
    Hazard warning light signal
    Answer-back OFF
    10 to 14 V
    *1: LHD
    *2: RHD
    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK CERTIFICATION ECU
B108931E01
  1. Disconnect the D60 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B1 (D60-1) - Body ground
    B - Body ground
    +B power supply
    Always
    9 to 14 V
    IG (D60-18) - Body ground
    BR - Body ground
    Ignition power supply
    Ignition switch on (IG)
    9 to 14 V
    IG (D60-18) - Body ground
    BR - Body ground
    Ignition power supply
    Ignition switch off
    Below 1 V
    LIN (D60-10) - Body ground
    P - Body ground
    LIN line
    Always
    10 kΩ or higher
    E (D60-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    RSSI (D60-39) - Body ground
    W - Body ground
    Door control receiver output
    Ignition switch off, all doors closed and transmitter switch not pressed → pressed
    6 to 7 V → Below 1 V
    RDA (D60-38) - Body ground
    R - Body ground
    Door control receiver intput
    Ignition switch off, all doors closed and transmitter switch not pressed → pressed
    Below 1 V → 6 to 7 V → Below 1 V
    RCO (D60-29) - Body ground
    L - Body ground
    Door control receiver intput
    Ignition switch off, all doors closed and transmitter switch not pressed → pressed
    5 to 0V → 5 V
    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK DOOR CONTROL RECEIVER
B123878
  1. Disconnect the door control receiver connector.

  2. Measure the resistance of the wire harness side connectors.

    Standard resistance: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (J13-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the door control receiver connector.

  4. Measure the voltage of the wire harness side connector.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    RSSI (J13-2) - Body ground
    W - Body ground
    Door control receiver output
    Ignition switch off, all doors closed and transmitter switch not pressed → pressed
    6 to 7 V → Below 1 V
    DATA (J13-5) - Body ground
    R - Body ground
    Door control receiver intput
    Ignition switch off, all doors closed and transmitter switch not pressed → pressed
    Below 1 V → 6 to 7 V → Below 1 V
    +5 (J13-4) - Body ground
    L - Body ground
    Door control receiver intput
    Ignition switch off, all doors closed and transmitter switch not pressed → pressed
    5 to 0V → 5 V
    If the result is not as specified, there may be a malfunction in the wire harness.

← PROBLEM SYMPTOMS TABLE (from Aug 2005)DIAGNOSIS SYSTEM (from Aug 2005) →