2005-2008 Yaris · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Nov 2005


CHECK INTAKE AIR CONTROL SYSTEM
  1. Check for leakage or clogging between the air cleaner housing and turbocharger inlet, and between the turbocharger outlet and cylinder head.

    Condition
    Operation
    Clogged air cleaner
    Clean or replace element
    Collapsed or deformed hoses
    Repair or replace
    Leakage from connections
    Check each connection and repair
    Cracks in components
    Check and replace


CHECK EXHAUST SYSTEM
  1. Check for leakage or clogging between the air cleaner housing and turbocharger inlet, and between the turbocharger outlet and exhaust pipe.

    Condition
    Operation
    Deformed
    Repair or replace
    Foreign matter in passages
    Remove
    Leakage from components
    Repair or replace
    Cracks in components
    Check or replace


CHECK TURBOCHARGER PRESSURE

A118834E01
  1. Warm up the engine.

  1. Using the three way connector, connect SST (turbocharger pressure gauge) to the hose leading to the intake air connector.

    SST
    09992-00242  

  1. For Manual Transaxle.

    1. Depress the clutch pedal, and then fully depress the accelerator pedal. Measure the turbocharging pressure at maximum speed (approximately 5,100 to 5,250 rpm).

      Standard pressure:
      15 to 45 kPa (0.15 to 0.46 kgf/cm2, 2.2 to 6.5 psi)

      1. If the pressure is less than the minimum, check the intake air and exhaust system for leakage.
      2. If there is no leakage, check whether the actuator hose is disconnected. If not, check the turbocharger.
      3. If the pressure is greater than the specified level, check whether the actuator hose is disconnected or cracked. If not, check the turbocharger.

  1. For Multi-mode Manual Transaxle.

    1. Fully depress the accelerator pedal. Measure the turbocharging pressure at maximum speed (approximately 5,100 to 5,250 rpm).

      Standard pressure:
      15 to 45 kPa (0.15 to 0.46 kgf/cm2, 2.2 to 6.5 psi)

      1. If the pressure is less than the minimum, check the intake air and exhaust system for leakage.
      2. If there is no leakage, check whether the actuator hose is disconnected. If not, check the turbocharger.
      3. If the pressure is greater than the specified level, check whether the actuator hose is disconnected or cracked. If not, check the turbocharger.


CHECK TURBINE SHAFT ROTATION

A110324
  1. Grasp the edge of the turbine shaft and turn it. Check that the turbine shaft turns smoothly.
    If the turbine shaft does not turn or is difficult to turn, replace the turbocharger.


CHECK TURBO PRESSURE SENSOR

A118833E01
  1. Inspect the power source voltage.

    1. Disconnect the turbo pressure sensor connector.

    2. Turn the ignition switch on (IG).

    3. Using a voltmeter, measure the voltage between the terminals of the wire harness side.

      Standard voltage:
      Tester Connection
      Specified Condition
      1 (E2) - 3 (VC)
      4.5 to 5.5 V

      If the result is not as specified, inspect the wire harness or ECM.

    4. Turn the ignition switch off.

    5. Reconnect the turbo pressure sensor connector.

  1. Check the power supply.

    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect an intelligent tester to the DLC3.

    4. Turn the ignition switch on (IG) and turn the tester ON.

    5. Select the following menu items: Powertrain / Engine and ECT / Data List / PIM.

    6. Disconnect the vacuum hose from the turbo pressure sensor.

    7. A118836E01
      Apply negative pressure to the turbo pressure sensor and confirm that a vacuum occurs.
      If the result is not as specified, replace the turbo pressure sensor.

    8. A118835E01
      Using SST, Apply pressure to the turbo pressure sensor and make sure that the pressure increases.
      SST
      09992-00242  
      If the result is not as specified, replace the turbo pressure sensor.

← SYSTEM DIAGRAM (from Nov 2005)COMPONENTS (from Nov 2005) →